Filter Results By:
Products
Applications
Manufacturers
Solenoid
Act as a magnet when current flows through moving an iron core.
- Pickering Interfaces Inc.
product
Single 12-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-014
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
product
DC Gaussmeter
GM1-HS
The Model GM1-HS measures the strength and polarity of magnetic fields up to 799.99 gauss. The thin sensor is at the end of a 100 cm flexible cable. The sensor tip is also flexible and can be bent for a variety of situations. The sensor can be held against the surface of a steel part to check for residual magnetism, or it can be bent into an "L" shape to measure inside a DC Solenoid. This meter has a resolution of .01 gauss (1/50 of the Earth's typical field) which is finer resolution than the Model GM1-ST. It is also used to map fields from large magnets (If fields are over 800 gauss, use the Model GM1-ST). The meter has immediate turn-on and updates 4 times a second. There is no setup required, making this the fastest gaussmeter available.
-
product
Stored Energy Solenoid Drivers
B-1014
The remote contact controlled HCA Series and the SCR controlled HCB Series of Stored Energy Solenoid Drivers produced by Ross Engineering Corporation are used for high speed opening or closing of Ross Circuit Breakers and Contactors. They perform high speed microseconds to milliseconds actuation of various electromechanical devices. The units feature minimum internal time delay, trigger signal overload protection, and up to 3000 joules of energy storage.
-
product
PXI Single 8x2 1-Pole 10A Power Matrix
40-551-002
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, the 8x4 module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
product
Solenoid Tester
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• High Reliability with Proven Design• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility• Integral Statistical Reporting• Test Data May be Stored in Multiple Formats• Two Year Warranty on Electronics
-
product
PXI General Purpose 2A Relay Module 32xSPST
40-132-201
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
product
Keysight 20-Channel 5A Form A Switch for 34980A
34938A
The Keysight 34938A is a high power general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 20 independent single-pole, single-throw (SPST) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. Its 30VDC/250VAC, 5A contacts can handle up to 150W on a single channel, enough for many power line switching applications. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
product
16 Channel Power PXI Multiplexer, 2 Pole
40-650-002
A 16 Channel Power Multiplexer, suitable for switching inductive/ capacitive loads up to 5A at 250VAC. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. It is suitable for applications requiring switching of either mains voltage or DC.
-
product
6-24V Heavy Duty Circuit Tester
1672
Peaceful Thriving Enterprise Co Ltd
Check on 6, 12 and 24V systems.1. Locate short, ground and open circuit.2. Make it easy to find out where current is present.3. The most essential for troubleshooting automotive electrical systems.4. Checks series-parallel switch and solenoid on tractor-trailer start systems.
-
product
NI-9475, 60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module
780132-01
60 V, 8-Channel (Sourcing Output), 1 µs C Series Digital Module - The NI‑9475 works with a variety of industrial devices such as solenoids, motors, actuators, relays, and lamps. Each channel sources up to 1 A at levels up to 60 VDC and features isolation from … channel‑to‑earth ground.
-
product
PXI General Purpose 2A Relay Module 26xSPDT
40-131-201
These are low cost, general purpose electromechanical relay cards capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
product
PXI 40Amp 14Volt 4xSPST Automotive Relay
40-180-101
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
product
PXI 2x SPST Power Relay, 2 Slot
40-170-001
Model 40-170 is available either as 2 x SPST High Power Relays, suitable for switching inductive/ capacitive loads up to 30A at 250VAC or as 2 x DPST switching up to 20A. Power Relay Modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
PXI 50 x SPST Ruthenium Reed Relay Switching
40-140A-021
This range of high density reed relay switching modules are available in Normally Open (SPST & DPST) and changeover (SPDT) configurations. Connections are made via a front panel 200 pin female connector. General purpose reed relays are suitable for the construction of small switching networks, for slaving up to larger switches or for operating external devices (e.g. lamps, solenoids etc.).
-
product
PXI Semi-Dynamic Digital I/O Module, 48-Channel
40-419-002
The 40-419-002 is a 48-channel digital I/O module suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. It can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
product
Keysight 32-Channel FormC/Form A General Purpose Switch for 34980A
34937A
The Keysight 34937A is a general-purpose switch module for the 34980A Multifunction Switch/Measure Unit. It has 28 independent single-pole, double-throw (SPDT) 1A relays and 4 single-pole, single-throw (Form A) 5A relays. This module is used to cycle power to products under test, control indicator and status lights, and to actuate external power relays and solenoids. The Form C channels are 300V, 1A contacts and can handle up to 60W, and the Form A channels are 30VDC/250VAC, 5A contacts and can handle up to 150W. Standard 50-pin Dsub connectors allow for use with standard cables, terminal blocks, or mass interconnect solutions.
-
product
Basic Pneumatic Trainer
Unitech Scales And Measurements Pvt. Ltd
It consists of a basic pneumatics kit components for, FRL unit solenoid valve, cylinder etc. This basic pneumatics kit shall be capable of being used to demonstrate to the design, construction and circuits.
-
product
Mechanical Shock Test System
BW-MST-E5000
The Mechanical Shock Tower develops the kinetic energy electromagnetically. An iron core "bullet" is attracted to the magnetic core of the solenoid by the dense magnetic field that is created as current flows through the field coil of the shock tower. As the bullet is drawn into the center of the magnetic field the acceleration increases exponentially as the gap reduces to zero on impact causing the high impact shock
-
product
PXI 5A Power MUX, 8-Bank, 5-Channel
40-651-004
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
Electric Linear Actuators
MaxJac
The MaxJac actuator features a smooth high response ball screw and gear motor and utilizes a proprietary guidance bushing to provide precision smooth linear actuation. Standard equipment includes a 12 volt motor with potentiometer feedback. It is ideal for throttle control, solenoid actuation, and valve actuation in such applications as construction equipment, motor vehicles, marine, and blood infusion pumps.
-
product
Power Switches
SMX-2002 (Power)
The SMX-2002 is the only switch module in its class with the ability to switch up to 16A. Some applications include: AC line power switching, switching of DC or AC power supplies, control or driving relays for industrial machines (robotics, numerical control machines), automotive engine control, and solenoid switching. Since this module typically switches power to the UUT or interface, the SMX-2002 includes failsafe pins on the front panel which can be configured to open all relays when a failsafe signal is activated. This approach can instantly removes all power to the UUT or interface.
-
product
PXI 5A Mux 2-Bank 24-Ch Isolated COM
40-651-012
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel.Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
PXI General Purpose 2A Relay Module 16xDPST
40-132-102
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
product
PXI Multiplexer, Very High Power DC, 4-Channel, 20A, 28V
40-664A-002
The multiplexer is suitable for switching heavy loads or for slave switching large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of DC voltage at high current.
-
product
PXI SPDT Switch: 26-ch, 2A, Armature Relay
M9130A
The M9130A is a general purpose switch with 26 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids. The armature relays can handle up to 60W power. When needed, these relays can handle up to 6A pulsed carry current. Choose from the durable connector block or standard cable connections.
-
product
PXI 8x4 1-Pole 10A Matrix With Loop-Thru
40-551-101
Used for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. X and Y connections are made via a 20-way GMCT plug, this module with loop-thru has an additional 20-way GMCT plug for module-to-module connection. This version of the 40-551 may be expanded to larger matrix sizes using cabling to daisy-chain the X and Y signals Power Matrix Modules are intended for switching heavy AC or DC loads or for slaving large external relays, contactors and solenoids. Suitable for applications requiring switching of either mains voltage or direct current.
-
product
PXI 5A Mux 1-Bank 48-Ch Isolated COM
40-651-011
This range of high density power multiplexer modules is suitable for switching inductive/capacitive loads up to 5A at 250VAC. It is available in the following 1-pole multiplexer formats: 1-bank 48-channel. 2-bank 24-channel. 4-bank 11-channel. 8-bank 5-channel. Connections are made via a front panel 50-way male D-type connector. Power multiplexer modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids.
-
product
Coaxial Switch, DC to 4 GHz, SPDT, 75 Ohms
8762F
The Keysight 8762F brings a new standard of performance to 75-ohm coaxial components. Designed for ATE switching systems, the Keysight 8762F offers the performance demanded by the cable television distribution equipment and communications equipment industries. It gives the ATE system designer of telecommunications and cable distribution equipment the tools to design reliable, high performance switching interfaces. The Keysight 8762F uses a mini 75-ohm SMB connector for the coaxial interface. The mini 75-ohm SMB connector is designed to terminate RG-179 75-ohm coaxial cable. The Keysight 8762F is designed to work in virtually any system due to the range of voltage options covering 4.5 V to 30 Vdc available for activating the switch solenoids. The standard configuration of the switch includes solder terminals.
-
product
64-Channel 250kSa/s USB Modular Multifunction Data Acquisition
U2355A
The U2355A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2351A to simulate simultaneous analog input acquisition.
-
product
64-Channel 1MSa/s USB Modular Multifunction Data Acquisition
U2331A
The U2331A offers multifunction capabilities in a module. It can be used like a digital multimeter in polling mode. It can be transformed to be a simple scope using the continuous mode with simple triggering capabilities. No matter if it is used as a standalone module or when plugged into a U2781A USB modular instrument chassis, the synchronization and triggering capabilities allow great flexibility in making the desired measurements. With the analog output being able to send out predefined or arbitrary waveforms make this a good tool when closed loop feedback or stimulus is required. The digital IO channels allows for closed loop control through connections to switches, relays and solenoids. The burst mode enables the U2331A to simulate simultaneous analog input acquisition.
-
product
Shield
Arduino Motor Shield Rev3
The Arduino Motor Shield is based on the L298 (datasheet), which is a dual full-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Arduino board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor, among other features. The shield is TinkerKit compatible, which means you can quickly create projects by plugging TinkerKit modules to the board.
