Filter Results By:
Products
Applications
Manufacturers
Protocol
A standard way of controlling hardware and/or software that enables connection, communication and data transfer.
See Also: NTCIP, Communication Protocol
- Virginia Panel Corporation
product
PCB Adapters - SIM
SIM PCB Adapters provide flexibility and modularity where custom PCBs cannot. Mix and match small modular boards to create a custom solution. Move SIM PCB adapters around to optimize space, mix protocols and match with patchcords. Combine protocols in a VPC SIM module and swap boards as your requirements change.
-
product
Embedded Protocol Decode/Trigger Software for USB 2.0, 10/100 ETH, PCIe 2/1 for Infiniium Oscilloscopes
D9010EMBP
D9010EMBP includes the following powerful protocol decode and trigger software: PCI Express Gen 1 and Gen 2, USB 1.1, USB 2.0, eUSB2, USB HSIC, USB-PD, 10BASE-T Ethernet, and 100BASE-TX Ethernet.
-
product
SAS (Serial Attached SCSI)
Serial Attached SCSI (SAS) is a data transfer technology designed to move data to and from storage devices such as disk drives, host bus adapters (HBA), and expanders. SAS is a serialized enhancement and replacement to parallel SCSI. Since SAS ratification in 2004, and it’s move to 6Gbps in 2008, Teledyne LeCroy has continued to support and innovate with it’s industry leading protocol analysis and traffic generation capabilities.
-
product
MILLENNIUM HEAVY-DUTY PRO CODE READER
MDM90HD
*Read and clear DTCs; read I/M readiness, data stream, freeze frame, O2 sensor info, on-board monitoring, vehicle information on (1996 and newer OBDII protocols based) vehicles*Read and clear DTCs; read data stream on heavy-duty (J1587, J1708, J1939, J1939/13 protocol based) vehicles*Supports 4 PIDs graphing at the same time
-
product
2 Channels, ARINC 568/579 Communications
AR2
The AR2 module provides an ARINC 568/579 communications interface with 2 channels. Channel 1 is Rx and Tx for ARINC 568 and channel 2 is programmable as either Rx or Tx for ARINC 579. This module only provides an interface and data management. Any specific protocol handling must be programmed by the user in the application layer.
-
product
Protocol Analyzer for PCI Express 5.0
Summit T54
The Summit T54 Protocol Analyzer captures, decodes and displays PCIe 5.0 protocol traffic data rates for x1, x2, x4 lane widths.
-
product
Infrared Gas Detector
iTrans2
Teledyne Gas & Flame Detection
The iTrans2 infrared gas detector employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs. With the optional HART Communication Protocol, the iTrans2 offers remote diagnostics, set-up or calibration by superimposing a high-frequency current across the industry standard 4-20mA analog line.
-
product
Infiniium V-Series Oscilloscope: 16 GHz, 4 Analog Channels
DSOV164A
16 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
PCI Express 4.0 Protocol Analyzer Exerciser
Summit T416
The Summit™ T416 analyzer is the computer industry's first high speed PCIe 4.0 protocol analyzer that meets the challenge of 16GT/s and up to x16 lane width protocol analysis. Many PCIe 4.0 product designs are already in progress using the PCIe 4.0 specification. Companies are currently working with the Teledyne LeCroy Summit Z416 protocol exerciser for PCIe 4.0 at the deployment of PCIe 4.0 for host system emulation with their testing needs. This combination of a protocol analyzer and exerciser make Teledyne LeCroy the only supplier of protocol test and development tools for PCIe Gen 4. High speed interposers that provide protocol analyzer connectivity to CEM or other form factor sockets on system boards will still continue to be the principle way to capture PCIe traffic into the protocol analyzer.
-
product
PCI / PMC / CompactPCI Test System
PCITS
The CPCI850 analyzer provides a multitude of functions to help you analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
Two Port SAS?SATA Analyzer
Sierra M122A
The Sierra M122A is Teledyne LeCroy’s two port SAS / SATA analyzer with special licensing to allow 6 Gb/s protocol capture. This multifunction platform is available with an integrated traffic generation option capable of host and device emulation. There is also a “Jammer” option for stress testing at the system and component level. This model of the Sierra M122A is configured for 6Gbps SAS & SATA protocol capture and can be field-upgraded to support 12Gb/s SAS testing.
-
product
TTL/I2C/SPI Expansion Kit
OP-SB85L
OP-SB85L is the interface expansion kit that has a port to measure TTL / CMOS signal level communications, and the one to measure the voltage of high-speed analog input. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communication between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI on monitoring and simulating.
-
product
EtherCAT Gateways
EtherCAT Fieldbus gateways provide seamless communication between Modbus RTU/TCP and EtherCAT communication protocols.
-
product
Optical Limiting Amplifiers
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
product
LANTIME Stratum 1 Server for all networks
Meinberg Funkuhren GmbH & Co. KG
Our Network Time Protocol (NTP) is the only way to get the most out of your network, to-use time server appliances.
-
product
Detective Logic Analyzer
LPDDR5
Provides logic analyzer like deep transaction Listing and Waveform capture. Can store up to 512M of captured States at up to 6400+ MT/sContinuous, real time analysis, not post-processing 2D (voltage & time) Eye Detector guarantees valid data acquisition on each signalExtensive Triggering and Storage Qualification allows precise insightIndustry Leading Protocol Violation Detector provides hundreds of simultaneous, real time tests to JEDEC specifications, NOT post processing. No other tool can provide this!Mode Register Listing provided
-
product
Load Cell Transmitter
MODEL SST-HV
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
product
Broadcast Recording And Compliance Logging System
AMR130
The Mividi® Broadcast Recording and Compliance Logging System (AMR130) provides a cost-effective solution for broadcast compliance monitoring and logging. It is a Windows PC based system that utilizes GPU encoding for low-cost video transcoding. The software supports stream recording, file management, editing and playback. The recorder takes transport stream input from UDP over IP or ASI interfaces, as well as Internet OTT streaming input using HLS, RTMP, RTSP, and MPEG-DASH protocols. A single system can support continuous recording of 30 streams.
-
product
Miniature Airborne Recording System
MARC II
The MARC II is a complete Miniature Airborne ReCording system designed to record messages of several communication protocols. Small, light, with low power consumption and large storage capacity for recorded data, the MARC II is the perfect standalone solution for airborne recording.Ethernet is built-in to the MARC II. In addition to Ethernet, you can order the MARC II with up to three additional modules of the supported protocols.
-
product
ARINC 818 Switch IP Core
ARINC 818-2 is a point-to-point, serial protocol, high bandwidth, low latency protocol for the transmission of uncompressed video, audio, and data during blanking period, widely used in AVIONICS application. Since a vast portion of the newer applications of the ARINC 818-2 have several displays with many channels of ARINC 818-2, switching has turned out to be more imperative. ARINC 818-2 switch can support up to 12 channels. Multiple switching modes such as broadcast, unicast, multicast, and mixed are also supported.
-
product
Serial-to-Daq Card
Model 2307
* 2307 Board provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Board. * DE-9 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * Runs on 5 Vdc power.
-
product
FTP Testing
TestingWhiz supports both File Transfer Protocol (FTP) and Secure Transfer Protocol (SFTP) testing. The application linked to an FTP server checks whether the data or actions performed by the user are reflected on the FTP server.
-
product
CompactPCI Instruments
Is a computer bus interconnect for industrial computers,combining a Eurocard-type connector and PCI signaling and protocols. Boards are standardized to 3U or 6U sizes, and are typically interconnected via a passive backplane. The connector pin assignments are standardized by the PICMG US and PICMG Europe organizations. The connectors and the electrical rules allow for eight boards in a PCI segment. Multiple bus segments are allowed with bridges.
-
product
cPCI / PXI / PXIe Crates
CompactPCI ratified as PICMG 2.0 in late 1995 is an interconnect bus standard for industrial computers, combining a 3U or 6U Eurocard-type card and PCI signaling / protocols via a passive backplane with metric connectors. PXI (PCI eXtensions for Instrumentation) is the application of CompactPCI for measurement and automation systems. PXI uses commercial PC-based PCI bus technology while combining rugged CompactPCI modular packaging with timing and synchronization features in order to provide an optimized basis for complex, rugged, modular instrumentation systems. The PXI standard is governed by the PXI systems Alliance (PXISA)
-
product
Multi-Layer Analysis for Next Generation PONs
Multi-ONU Emulator
The NG-PON Xpert multi-layer analyzer is a unique, real-time protocol analyzer for XG-PON1, NG-PON2 and XGS-PON networks and products. The Multi-ONU Emulator introduces a new revolutionary approach for comprehensive testing of an OLT. It enhances the testing with repeatable test scenarios and functionalities that cannot be tested in any other way, including the OLT's ability to handle various ONU models and configurations, error and defect conditions, alarms and traffic loads.
-
product
USB-7846, Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783201-02
Kintex-7 160T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7846 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
4 Digit Temperature Meter (5 Channels)
CM1-TX5
Chuan Sheng Electronics Co., Ltd.
RS-485 Modbus RTU protocol (with communication LED indicator)RS-485 address 1~255Communication Baudrate 9600, 19200, 38400, 57600, 115.2KParity check N81, N82, E81, O81Input 5 channels of signal selectable：thermocouple/PT100.5 channels of input can be set to play 1~10 seconds loop display.1~5 channels of display value limits can be set, and the number of channels of carousel display screens can be set by yourself.5 channels of input signals with LED unit cycle display.Standard 2 groups of alarms Hi, LO with communication LED indicators to ensure the normal operation of the field system.Suitable for HVAC refrigeration and air conditioning PLC, DDC, PC brands to achieve remote real-time monitoringCan be used in solar panels, medical control, clean room, ice water host, boiler, motor, chemical plant, power plant, school energy-saving control, remote control of power monitoring panel
-
product
Medium-size Reverberation Chamber
E-Series
The E medium-size multicavity Reverberation Chamber Series represents that state-of-the-art in reverberation chamber technology. The E-Series can make single measurements, batch tests, protocols or campaign tests for different frequency bands, different technologies and different channel models, running overnight without human intervention. Embedded frequency-, mode-, source- and platform-stirring in a double-shielded set of cavities allow Passive MIMO (Efficiency, Correlation, Diversity Gain, MIMO Capacity and others), Active MIMO OTA (TRP, TIS, TPUT, MTS, CQI, M2TxDT, RSRP, MCL and others) and Time-Domain MIMO (DL/UL TCP/UDP TPUT, RMS DS, STD, PL, CBW, Mute%, eNodeB, VDT-OTA) measurements up to 8x8 and 8DLCC to be performed for antennas and devices up to 50cm and 50kg ranging from 2G to 4G, covering all available cellular and wireless technologies to date, including wearables devices, sound acoustic mute, WLAN and W-IoT testing. There is no RC in the market more advanced than the E-Series.
-
product
HEV & EV Power Tester
EVd-40
The EVd-40 Power Tester is a pre- and post-reconditioning tool for quality control of aftermarket HEV & EV battery production. The equipment integrates a “smart” charger (Sorensen XG 1700 or Kepco KLN 1500W) with NuVant Systems high power discharge electronics. The "power test" discharges battery packs at high power (10,000 watts), while tracking module voltages. The software monitors up to 40 module voltages at a time, identifying any weak modules. The "smart" charger performs charging constant current (CC), constant voltage (CV) and complex mixed mode constant current – constant voltage (CCCV) charging protocols at voltages up to 600 V. This enables recharge of any type of rechargeable battery.
-
product
ProxiLAB Quest Contactless Tester
Fully programmable card (PICC), reader (PCD) and NFC signal emulator for device characterization and protocol conformance verification. ProxiLAB Quest offers the performance and features required for full characterization and conformance validation of all 13.56 MHz contactless technologies, including the latest very high bit-rate evolutions. ProxiLAB Quest integrates with a variety of conformance certification solutions and test automation platforms.
-
product
80Gbps Video Analyzer/Generator for DisplayPort 2.0 Testing
M42d
The Teledyne LeCroy quantumdata M42d Video Analyzer/Generator provides functional and will support compliance testing for video, audio and protocol of DisplayPort 2.0 and DisplayPort 1.4. The M42d supports legacy DisplayPort lane rates of 1.62, 2.7, 5.4, 8.1 Gb/s and the new DP 2.0 higher speed lane rates of 10.0, 13.5, & 20.0 Gb/s data rates with the new line coding—128b/132b. The protocol analyzer provides a snap shot status view and deep analysis using captures of incoming DisplayPort 2.0 streams from source devices including DSC/FEC compressed streams. The M42d’s video generator can be used for testing silicon as well as devices such as displays, USB-C adapters, extenders, etc. The video generator offers a large library of standard video timings and test patterns necessary for testing next generation high resolution displays.
