Filter Results By:
Products
Applications
Manufacturers
Physical Layer
Tests hardware, electrical and procedural interface to the transmission medium.
- Pickering Interfaces Inc.
product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 8-Channel, 2-Pole
40-739-004
The 40-739-004 (PXI) and 42-739-004 (PXIe) are dual 8-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
product
Ethernet Media Converter
A physical layer equipment which interconnects the Ethernet, Fast Ethernet, or Gigabit Ethernet on copper UTP and the related fiber optics network. Ethernet media converter meets corresponding IEEE 802.3 standards.
-
product
Optical Limiting Amplifiers
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
product
Network Cable Tester
NCT-500
ShinewayTech NCT-500 Network Cable Tester，Functions ranging from ISO / OSI reference model physical layer, link layer, network layer multiple detection. One machine in hand, which can quickly locate network faults and determine the link quality.
-
product
Fibre-Coaxial DOCSIS Analyzer
CABLERANGER
DOCSIS 3.0 analyzers for hybrid Fibre-Coaxial networks CABLE RANGER from PROMAX provide all the required measurements to install and carry the network maintenance of those hybrid networks using fiber optics and coaxial cables at the physical layer. The operating frequency range spans from 5 Mhz to 1700 Mhz, thus fulfilling DOCSIS 3.0 and 3.1 requirements.
-
product
PCIe Mini CAN Controller
PCie-Mini-CAN-FD
The PCIe-Mini-CAN-FD is a PCI express controller with an integrated CAN FD transceiver supporting data rates up to 8Mbps. The CAN FD controller meets the specifications of the ISO11898-1:2015 high speed Controller Area Network (CAN) data link layer and meets the physical layer requirements of the ISO11898-2:2016 high speed CAN specification.
-
product
EV-DO Analysis Using NI PXI RF Test Instruments
NI-RFmx EV-DO
Highly optimized RF measurement experiencePerform physical layer analysis on EV-DO cellular signals including MODACC, ACPR, CHP, OBW, and SEMSimple access to advanced measurement parallelism
-
product
64 Gbaud High-performance BERT
M8040A
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
product
PXI-8532, 1-Port, PXI DeviceNet Interface Module
781063-01
1-Port, PXI DeviceNet Interface Module—The PXI‑8532 is a high-speed DeviceNet interface for developing applications with the NI‑Industrial Communications for DeviceNet driver. DeviceNet is based on the CAN physical layer and increases strength and interconnectivity by specifying various parameters, such as the required cable length, connectors, and baud rates. DeviceNet specifications are managed by OVDA, Inc. You can program the PXI‑8532 to add high-performance master/scanner or slave capabilities to DeviceNet networks.
-
product
ARINC PC/104-Plus Interface Card
PC104P-A429
Alta Data Technologies’ PC104P-A429 interface module offer a variety of ARINC-419/429/575/573/717 channel configurations with software selectable RX/Tx channels, baud rates, bit encoding and word configurations (Start/Sync/Stop length, Parity, bits/word, MSB/LSB). Encode or decode almost any ARINC-429 physical layer signal.
-
product
PCI-8531, 1-Port, CANopen Interface Device
781060-01
The PCI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation … applications. CANopen was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The PCI‑8531 can transmit or receive process data objects (PDOs) and service data objects (SDOs) according to CiA‑DS 301. It also features a batch SDO editor with EDS file integration and LSS services support for slave node configuration.
-
product
4 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTF
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Bit Error Ratio Testers
M8000 Series
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
product
GSM/EDGE Analysis Using NI PXI RF Test Instruments
NI-RFmx GSM/EDGE
The NI-RFmx GSM/EDGE personality is a highly optimized API for performing physical layer measurements on GSM/EDGE cellular standard signals. NI-RFmx GSM/EDGE is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development effort.
-
product
2 Channels, MIL-STD-1553, Dual Redundant, Direct Coupled, Assisted Mode Capable (AMC)
FTE
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
AXIe M8000 Series of BER Testers
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
-
product
PLTS Measurement And Calibration
N19303B
The new Physical Layer Test System (PLTS) 2024 is the industry standard for signal integrity measurements and data post‑processing high-speed interconnects, such as cables, backplanes, PCBs, and connectors. Signal integrity laboratories worldwide have benefited from the power of PLTS in the R&D prototype test phase.
-
product
Iridium Physical Layer Test Systems
PLTS
Averna has worked with Iridium to ensure you have the right equipment to support their test coverage. The Iridium PLTS verifies product performance to Iridium’s standards. Find out more!
-
product
IsatData Pro Physical Layer Tester
DPLT
Square Peg Communications Inc.
The IsatData Pro Physical Layer Tester (DPLT) supports testing of the physical layer performance and protocol implementation of Mobile Terminals (MTs) implementing Inmarsat’s IsatData Pro (IDP) services.
-
product
1000BASE-T1 MEDIACONVERTER
Art.-Nr.: TE-1401-1
The ideal physical layer conversion between Automotive Gigabit Ethernet and your PC system The 1000BASE-T1 MediaConverter establishes one direct point-to-point conversion between automotive ECU’s using 1000BASE-T1 and any standard Gigabit Ethernet device with RJ-45 connector.
-
product
Chassis
RSM/128-MF
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or any combination or configuration such as a 16x8 matrix, 32x4 matrix or two 16x4 matrices. Matrix configurations are non-blocking and physical layer switches act like a cable connection with D connectors creating a one to one connection between D9, D15 or D25 connectors.
-
product
Efficient And Effective Physical Layer (PHY) Testing Of 10/100/1000Base-T Interfaces
Explore Sifos Technologies’ highly unique, plug’n play 10/100/1000Base-T Ethernet Physical Layer Testing Solutions. Cost Effective and Comprehensive PHY Testing without Scopes, Fixtures, Probes, and Test Signals.
-
product
SD Host Tester / SD / EMMC Analyzer / SD Card Tester
SGDK320A (SD Host Tester)
SGDK320A (SD Host Tester) is a product that has the functions of SD emulator (SD Emulator), host tester (Host Tester), SD analyzer (SD Analyzer), and eMMC analyzer (eMMC Analyzer). Supports SD Memory Card Physical Layer Specification Version 3.01. It covers the test contents of Test Specification Ver3.00 and Supplement Note. Supports SDR104 and eMMC ver4.41 (analyzer).
-
product
PXI/PXIe MIL-STD-1553 Multiplexer, Dual 16-Channel, 2-Pole
40-739-002
The 40-739-002 (PXI) and 42-739-002 (PXIe) are dual 16-channel 2-pole multiplexers designed specifically for physical layer multiplexing or demultiplexing differential signals that conform to the MIL-STD-1553 specification. The module can be supplied as a single or dual 16-channel 2-pole multiplexer with each signal pair having a controlled 78 Ohm differential impedance.
-
product
SAEJ1962M-DE9M CAN OBD-II Cable, SAE J1962 to D-sub 9-pos F, 2m
193942-02
9-Pin, Male SAE J1962 OBD-II Type A to 9-Pin, Female D-SUB - The OBDII9M-DB9F CAN Cable, sometimes referred to as the CAN OBD-II Cable, connects any NI high-speed CAN interface to an OBD-II compliant vehicle that has high-speed CAN on its diagnostic link connector in the passenger compartment. This high-quality injection-molded cable connects the CAN wires from the SAE J1962 connector to the standard CiA-DS-102 D-SUB connector wiring used by NI CAN interfaces. This cable is available with a high-speed CAN physical layer and no termination.
-
product
100BASE-T1 MEDIACONVERTER NXP
Art.-Nr.: TE-1600
The ideal physical layer conversion between Automotive Ethernet and your PC system. The 100BASE-T1 MediaConverter NXP establishes one direct point-to-point conversion between automotive ECU’s using 100BASE-T1 and any standard Fast Ethernet device with RJ-45 connector.
-
product
4 Channels, MIL-STD-1553, Dual Redundant, Transformer Coupled, Assisted Mode Capable (AMC)
FTC
MIL-STD-1553 is a military standard published by the United States Department of Defense that defines the mechanical, electrical, and functional characteristics of a serial data bus. It was originally designed for use with military avionics, but has also become commonly used in spacecraft On-Board-Data-Handling (OBDH) subsystems, both military and civil. It features a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
product
Physical Layer Test System
N19301B
The N19301B Physical Layer Test System (PLTS) 2022 software is a powerful signal integrity tool for today’s high-speed digital designers.
-
product
DVB-T2 Gateway module
T2Gateway
T2Gateway for HDc is ENENSYS’ DVB-T2 Gateway module (T2-base or T2-lite) that encapsulates one or several MPEG-2 Transport Streams into a DVB-T2 multiplex, inserts synchronization data for single frequency network broadcasting, allocates data into the different physical layer pipes and generates T2-MI packets over ASI and IP.
-
product
100BASE-T1 MEDIACONVERTER BCM
Art.-Nr.: TE-1000
The ideal physical layer conversion between Automotive Ethernet and your PC system. The 100BASE-T1 MediaConverter BCM establishes one direct point-to-point conversion between automotive ECU’s using 100BASE-T1 and any standard Fast Ethernet device with RJ-45 connector.
