Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm - SPST
50-294-121
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Extended Length RTSI Bus Cables for 5 PCI or AT/ISA Devices
777562-05
34-Pin Female RTSI to 34-Pin Female RTSI Ribbon Cable - The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
product
RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, CANbus, 2 LANs And DIO (2-in/1-out)
IFB112
The IFB112.supports the low power consumption NXP (Freescale) i.MX6UL ARM® Cortex™-A7 528MHz SoC. The design concept of IFB112 is aiming to meet the demands of mission-critical applications. The gateway controller with IP30-rated aluminum and steel enclosure supports an extended operating temperature ranging from -40°C to 70°C, a wide voltage range of 9V - 48V DC power input with terminal block, and has been designed to withstand vibration up to 5G. For system integrators with wireless communication needs, the IFB112 has one PCI Express Mini Card slot, one SIM card slot, and two internal antennas. It supports one serial port, two LANs and one CANbus port to enable fast and efficient data acquisition and communication. Its digital I/O port provides users with a convenience of digital devices connection.
-
product
AFDX® / ARINC 664 Test And Simulation PCIe Module
PCIe-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Robust DIN-rail Fanless Embedded System With Intel® Celeron® Processor N3350, 2 COM, LAN, 2 USB And DIO
ICO100-839
The ICO100-839 is a DIN-rail fanless embedded system designed to support the low-power Intel® Celeron® processor N3350. This DIN-rail industrial IoT gateway supports one DDR3L SO-DIMM slot with up to 8 GB system memory. Its proven rugged construction ensures reliable operation in harsh environments with an extended temperature range of -20°C to 70°C and anti-vibration up to 2G. Additionally, the wide range 12V-24V DC power input with a lockable terminal block type connector is suitable for industrial automation fields. The overvoltage and reverse protection lowers the risk of crucial data loss. The outstanding Intel® Atom™-based ICO100-839 is a perfect solution for industrial IoT applications such as smart factory automation and smart energy. The DIN-rail industrial IoT gateway offers an outstanding price/performance ratio with good quality. It comes with sufficient I/O connectivity while measuring only 31 x 100 x 125 mm. The I/O interfaces include two RS-232/422/485 ports, two USB 2.0 ports, one Gigabit Ethernet, one VGA and one DIO. Furthermore, the Intel® Apollo Lake-based ICO100-839 is equipped with two PCI Express Mini Card slots, one for mSATA storage card and another for 3G/GPRS/Wi-Fi connections.
-
product
PCI Express To CPCI Board
MS 1719
PCI Express to CPCI card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit cPCI signals from/to the Host System. These cPCI signals are converted into PCI Express using cPCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
product
Network Interface Card
PMC-GBIT-DT2BP
The Ethernet network interface complies with the IEEE 802.3 specifications for 10BaseT, 100BaseTX, and 1000BaseT over category 5 twisted-pair cable. Full-duplex and half duplex modes are supported. The PMC-GBIT-DT2BP is compliant with standard singlewide PMC IEEE P1386.1, PCI 2.2, and PCI-X 1.0 specifications.
-
product
PCI-X Carrier For AMC Modules
PCI102
The PCI102 allows testing of AMC.1, AMC.2 and AMC.3 modules in a PC environment during development and manufacturing; reducing the costs associated with maintaining different platforms. The PCI101 is a PCI-X edge style carrier with PCIe x4 lanes going to the AMC module. The AMC.1 module connects to the host PC’s PCI-X bus via a PCI-X to PCI ebridge. The AMC.2 module’s GbE ports are routed to RJ-45s. The AMC.3 differential pairs are routed to two SATA connectors. ThePCI102 is available with an optional VT001 IPMI controller which can test the AMC IPMI management functionality. The dual I2C bus connectors allow for connecting any I2C bus to any other I2C bus as well as being able to debug and monitor the I2C bus traffic. Provides two current sense resistors to measure the payload power as well as the management power of the AMC. The PCI102 can be powered on the bench without the host PC.
-
product
Shared Memory Network PCI & PCIx Interface
PCI-SMN
Avionics Interface Technologies
2.125 Gbps Optical loop network - Single-mode and Multi-mode optical interfaces supported - Up to 256 Shared Memory Network nodes supported - Up to 200 MByte/sec sustained data rates - Maximum 500 nS latency between nodes - Network interrupts supported - Compatible with PCI & PCIx Host System Slots - Software Drivers available for Windows, Linux, LabVIEW Real-Time, and VxWorks
-
product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - 6U VPX
Model 57671
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Four 1.25 GHz 16-bit D/As- Four digital upconverters- Extended interpolation range from 2x to 1,048,576x- Programmable output levels- 250 MHz max. output bandwidth- 2 GB of DDR3 SDRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- Dual µSync clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-6 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Synchronize up to twelve modules with Model 9192 System Synchronization and Distribution Amplifier- 1U Rack-mount
-
product
AFDX ® / ARINC 664 Test And Simulation PCI Module
PCI-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
MIL-STD-1553 Test & Simulation Interface for PCI
PCI-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - PCI & PCIx Compatible, 3.3V and 5V OperationApplication interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
6U Dual 64/100 PMC VME Carrier
V2PMC2
The V2PMC2 PCI-X/PMC carrier card is a 6U VME that holds up to two single-width or one double-width PCI-X/PMC modules. The V2PMC2 works in association with a PCI-Express host which is connected to it through a x4 PCI-Express serial link onto P0 connector.
-
product
PCI and PCI-X Bus Analyzer / Exerciser
PCI850
The PCI850 analyzer provides a multitude of functions to help analyze your system.- Capturing bus activity using sequential triggers and filters- Exerciser to perform memory, I\O and configuration cycles- Stimulus generation for hardware simulation- Target memory with addressable windows- Anomaly detection of protocol and timing violations- Performance analysis of utilization, transfer rates, latency, statistics- Compliance testing
-
product
Express Multi Protocol Board
EXC-8000PCI
The EXC-8000PCIe is a PCI Express card supporting up to eight independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched on a single card. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The EXC-8000PCIe supports extensive error injection and detection capabilities, IRIG B Time Code input, and can be ordered with an extended operating temperature range of -40ºC to +85ºC and conformal coating. The EXC-8000PCIe is supplied with C drivers, including source code.
-
product
Pico-ITX SBC With Intel® Pentium® Processor N4200 & Celeron® Processor N3350, LVDS And LAN
PICO313
The PICO313 features the Intel® Pentium® processor N4200 or Celeron® processor N3350, aim at the entry-level market. It runs fanless, supporting +12VDC power input, slim I/O and extended temperature range. The Pico-ITX motherboard has one 204-pin DDR3L-1867 SO-DIMM socket with up to 8 GB memory. One full-size PCI Express Mini Card slot with support of mSATA and one half-size PCI Express Mini Card slot are available on the rear side of the board. Additionally, a pair of expansion connectors provides signals for one PCIe lane, one LPC, one DDI, four USB 3.0 ports, one SMBus, and one HD audio to meet different communications needs.
-
product
PCI I/O Products
Our PCI boards are based on technology and circuit designs with time-tested reliability in thousands of installations. Great effort goes into selecting high-performance parts to withstand the demands of military, aerospace, and manufacturing applications. Most models are available with extended temperature ranges for reliable operation in harsh environments. Acromag products are also designed for the long lifecycles required for OEM and defense projects.
-
product
32/64 Bit 33/66 MHz PCI-X to PMC-X Adapter
4044
32/64 Bit 33/66 MHz PCI-X to PMC-X Adapter. The PCI-X to PMC-X Adapter permits operation of a standard 32 or 64 bit PCI-X card in a PMC-X slot. It provides a migration path for PCI-X board suppliers to port their products to a PMC-X form factor. As the PMCX equivalent board is developed, software development and migration can proceed with the original PCI-X board operating in a PMC-X environment.
-
product
PCI Extender Card for cPCI Systems
DP-cPCI-7497
The DP-cPCI-7497 is highly flexible PCI Extender card, which can be used to extend PCI / PCI-X bus from one system to another system over an optical fiber medium upto 500m distance. A PCI-X to PCI-e Bridge is used to convert the PCI / PCI-X protocol to x4 PCI Express protocol operating at 2.5Gbps.The PCI-X to PCI-e Bridge is connected to four optical transceivers (x4 PCI- e link) which can transmit optical signals upto 2.5Gbps speed.A x4 copper medium connection option in lieu of optical transceivers is also available.
-
product
Digital Input/Output and Counter/Timer Card
PCI-DIO-96C3
This is a 96 line digital input/output card with counter/timer capabilities designed for use in high I/O density application requirements. I/O connections are made via four 50-pin header connectors. The card is 12.25 inches long (312 mm) and may be installed in any full-length 5V PCI-bus (or PCI-X bus) slot in X86 type PC’s.
-
product
CANbus Controller Standard Interface
PCI360
The PCI360 CANbus controller PCI card is based on the SJA1000. The SJA1000 provides an interface to the popular CANbus that support both standard (11-bit) and extended (29-bit) identifier messages. LEDs provide diagnostics information.The CAN network is a serial communication protocol which efficiency supports distributed real-time control with a high level of reliability.
-
product
RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, LAN, DIO (2-in/2-out), 4 AI Channels (16-bit, 250 KS/s) And 2 PCIe Mini Card Slots
IRU152
The IRU152 is powered by the low-power NXP i.MX 6 UltraLite processer. It can withstand an extended operating temperature range of -40°C to +70°C and up to 2G of vibration for operating in harsh environments. Furthermore, it supports NI LabVIEW to allow users to design graphical user interfaces for their measurement applications quickly and efficiently. In order to provide data collection and device control, the IRU152 comes with various I/O connectors, including four analog input (AI) channels, one isolated RS-232/422/485 port, one isolated LAN and one isolated DIO (2-in/2-out). The four analog input channels have differential input configuration and overvoltage protection of 55V DC. The maximum sampling rate of IRU152 is up to 250 kS/s with a 16-bit resolution for low-speed high-resolution sensor monitoring and signal measurements. Apart from the abovementioned features, the IRU152 comes in two PCI Express Mini Card slots and one SIM card slot for Wi-Fi, 3G/4G and LoRa connections. The DIN-rail embedded system is equipped with onboard 512MB DDR3 SDRAM; besides, they have an 8GB eMMC flash memory. The extremely low power industrial IoT gateway has passed the Heavy Industrial certification and FCC part 15 to ensure the excellent quality and highly reliable performance.
-
product
Multifunction Analog I/O Card
LPCI-AIO16A
Model LPCI-AIO16A provides 500k samples/second, with 16-bit resolution, for the board’s 16 single-ended or 8 differential analog input channels. Also included are two 12-bit analog outputs, 16 digital I/O lines and an 8254 with three 16-bit counter/timers. The board meets the MD2 Low Profile PCI Bus Specification and can be installed in any 3.3V or 5V PCI or PCI-X slot.
-
product
PCI/USB Device Driver Development Tool
WinDriver
The WinDriver™ device driver development tool supports any device, regardless of its silicon vendor, and enables you to focus on your driver’s added-value functionality, instead of on the operating system internals. WinDriver’s driver development solution covers USB, PCI, PCI Express, CardBus, CompactPCI, ISA, PMC, PCI-X, PCI-104 and PCMCIA.
-
product
1 PICMG® CPU, 1 PCI-E® x16,1 PCI-X™, 2 PCI™ Slots Backplane
EBP-5E1
- Segment: 1- Slots:1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-X™, 2 PCI™- Support ATX power supplies- Dimension: 153 mm x 330 mm
-
product
Robust DIN-rail Fanless Embedded System With Intel® Celeron® Processor N3350, COM Or CAN, 2 LAN, 2 USB And DIO
ICO120-83D
The ICO120-83D is powered by the Intel® Celeron® processor N3350. The embedded filed controller supports one DDR3L-1866 SO-DIMM slot with up to 8 GB of system memory. It is equipped with one full-size PCI Express Mini Card slot, one half-size PCI Express Mini Card slot in support of mSATA, and one SIM socket to provide flexible extension capability. The ICO120-83D measuring only 31 x 100 x 125 mm is well-suited for space-constrained deployments. It offers an IP40 extruded aluminum and heavy-duty steel design for durable use. This powerful industrial IoT gateway can withstand harsh operating conditions with an extended temperature range of -20°C to 70°C and vibration resistance up to 2G. Additionally, the unit supports a wide voltage range of 12V to 24V DC power input with overvoltage and reverse protection.
-
product
Virtex-5 FPGA with Plug-in I/O
PMC-VSX
Acromag’s PMC-VSX boards feature a reconfigurable Xilinx® Virtex™-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCI-X interface. Field I/O interfaces to the FPGA via the rear J4/P4 connector and/or with optional front mezzanine plug-in I/O modules. The result is a powerful and flexible I/O processor module that is capable of executing your custom instruction sets and algorithms.
-
product
Virtex-5 FPGA with Plug-in I/O
PMC-VFX
Acromag’s PMC-VFX boards feature a reconfigurable Xilinx® Virtex™-5 FPGA enhanced with multiple high-speed memory buffers and a high-throughput PCI-X interface. Field I/O interfaces to the FPGA via the rear J4/P4 connector and/or with optional front mezzanine plug-in I/O modules.
-
product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, 2 COM, 2 LANs And DIO (2-in/1-out)
IFB122
The IFB122 is an extremely compact RISC-based DIN-rail industrial IoT gateway powered by the low-power Freescale i.MX 6UL-2 processor in the ARM® Cortex™-A7 micro architecture. Designed to meet the challenges in critical environments, it supports extended operating temperature ranging from -40°C to 70°C, flexible wide voltage range 9V - 48V DC power input, and can withstand vibration up to 5G. One PCI Express Mini Card slot, one SIM card slot, and two internal antennas are available for Wi-Fi and 3G/4G connections. With the abilities to transmit data and manage various devices, the IP40-rated ready-to-run IFB122 is definitely a cost-effective solution for remote control/monitoring management applications such as unmanned control room, industrial machine, automatic parking lot, traffic cabinet, etc.
-
product
Two Port Fibre Channel/MIL-STD-1760E Network Interface Controller
cPCI-HS1760-NCSW-2
Avionics Interface Technologies
Integration of Up Fibre Channel and Down Fibre Channel interfaces - Embedded Network Controller (NC) with four priority levels - Two F/AE ports for communication to external devicesInternal four port non‐blocking fabric switch for communication between NC and external devices - Four port non‐blocking Fibre Channel Switch - Meets the requirements of MIL‐STD‐1760E and AS5653 standards - Initialize via the Fast Fabric Initialization (FFI) protocol - ANSI C API enabling complete FC-AE-1553 NC functionality and management - 3U Conduction-cooled Compact PCI module - Designed for extended temperature operations
-
product
Gigabit Ethernet PCI Express Mini Card
mPCIe-LAN-GbE
The mPCIe-LAN-GbE is a type F1 PCI Express Mini Card (mPCIe) optimized for use in mobile and rugged environments, with latching connectors and protection on all signals. The onboard magnetics feature robust built in isolation via transformer coupling. In addition, extended operating temperature and RoHS compliance are standard.
