Filter Results By:
Products
Applications
Manufacturers
Insulation Test
Check of a materials ability to prevent or reduce transmission.
See Also: Impulse Winding Testers
- Pickering Interfaces Inc.
product
Switching System Test Tools
EBIRST™
Switching systems are an important part of many test systems, however, the switching system is in a vulnerable place. When accidents happen that can cause a faulty device, you need a way to get the system up and running again with a minimum of effort and operator skills.
-
product
Digital Insulation Tester
200M
Laxtronics Instruments & Controls Pvt. Ltd
Digital insulation tester Model No: DIT200M is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage from 1 to 30 Volts DC, its short circuit current is less than 100uA. The instrument can measure Resistance from 1 Meg Ohm to 1000 Meg Ohms.
-
product
Guardian Hipot Analyzer
19056/19057
Chroma Systems Solutions, Inc.
Chroma’s Guardian 19056/19057 Hipot Analyzer is specially designed for testing and analyzing ultra-high withstand voltage. The series of models include 10kVac / 12kVdc / 20kVdc with maximum AC20mA / DC10mA output that can perform AC / DC withstand voltage and insulation resistance tests with contact check during production line test.
-
product
Electrical Test Calibrators
The electrical test calibrators from Time Electronics are designed for rapid calibration of various electrical test equipment. Portable calibrators include the InsCal models for insulation tester calibration and the PatCal for calibration of portable appliance testers.
-
product
Inductor Tester
An impulse can be applied to the coil of a chip power inductor to perform insulation tests (surge tests) within the windings.
-
product
Insulation & Multifunction Tester (OLED Display)
1155 TMF-M
Standard Electric Works Co., Ltd
● High Contrast OLED display.● Designed for viewing in the dark, for mining industry.● Auto-range microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto-discharge on all tests and all ranges.● Leads auto-null key.● Test auto-stop.● Smart hold and stop on voltmeter AC/DC.● Ener-Save.● Continuity short circuit >220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Polarization index (PI).● Dielectric Absorption Ratio (DAR).● BS 16 edition.
-
product
Multifunction Installation Tester
COMBI519
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
product
Insulation / Continuity Tester Proving Unit
PU250
The PU250 allows simple and quick check of insulation resistance and continuity for all makes of I/R testers.Regular checks outside of the formal calibration process are required for compliance with BS7671 and Part P.Proving unit to enable compliance to the requirement to maintain records of regular checks on the measurement characteristics and accuracy of test instruments.
-
product
Pulse - Generator
PG 01-2000
The test generator PG 01-2000 is suitable for insulation test and testing of the impulse withstand voltage of electrical and electronic electricity meters. The generator produce a standard pulse voltage waveform with 0,1 / 2000 μs.
-
product
Line Testers
GAOTek provides a large collection of certified and feature-rich line testers for sale to the United States, Canada and Globally. These devices are mainly used for line installation, line performance testing, inspection, and maintenance of the telecommunication networks. They are particularly designed to accelerate telecom trouble shooting and with the help of latest technology they are equipped with a smart CPU, IC, and SMT. These devices have some unique features such as caller ID display and last number redial. Moreover, it can also be used for multi-line testing, wire pair checking, inspection of line insulation and test for breaks and faults.
-
product
Analogue (1kV below) Insulation Tester
1832 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on low ohms : 3Ω & 500Ω.● Compact and lightweight.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● BS 16 edition.
-
product
Multi-function Tester
MFT5010
It can be used to test insulation resistance, continuity, loop impedance and RCCB, earth resistance tester, five major test requirement in the electrical testing industry. Phase indicator. Can check a wide range of 3-Phase Power source from 110V to 600V
-
product
Impulse Voltage Generator
SKS-255I
Shanghai Sanki Electronic Industries Co., Ltd.
The impulse voltage generator SKS-255I is manufactured in accordance with the IEC60255-5 "Insulation Test of Electrical Relays" promulgated by the International Electrotechnical Commission. It measures the insulation coordination between relays and protection devices and performs impulse voltage tests.
-
product
Automatic Wire Test Set
AWTS
The Automatic Wire Test Set (AWTS) is automated test equipment that aids wiring diagnostics of electrical and electronic devices. The Test Control Unit (TCU) uses resistance measurements, capacitance measurements, and AC/DC voltage measurements to perform continuity, insulation, and isolation tests. The AWTS Laptop CPU, hereafter referred to as CPU, controls the AWTS. The Eclypse Language Integrated Test Environment (ELITE) is application software that controls the TCU. The majority of the hardware for a test is contained in the TCU. The 128pin connector on the TCU front panel provides 128 energizable test points. Switch Modules (SM) can be connected in sequence or daisy chained to the TCU and provide an additional 1024 test points; 128 of those are energizable.
-
product
Insulation Multimeter Series
Insulation Multimeter is a new category of test tool that combines a full featured True-rms DMM and a megohmme- ter. It's an integrated tool for maintaining and troubleshooting motor systems, electrical distribu- tion, and production equipment.
-
product
High-Voltage Test and Diagnostics Device
Viola
BAUR Prüf- und Messtechnik GmbH
Cable testing and diagnostics with the BAUR viola. The portable and powerful viola high-voltage testing and diagnostics device is used for cable and cable sheath testing of medium-voltage cables up to 35 kV and electrical equipment. Another function is insulation testing on electrical equipment.* High performance and compact* Precise and non-destructive determination of the cable condition* Easy and quick test setup* Automatic testing and diagnostic sequences
-
product
Electrical Safety Testers
.AC/DC withstand voltage test & ground bond test .Insulation resistance test(ST60).Arc detection.Zero crossing turn-on,turn-off operation switch.Controllable ramp-up time .Ture RMS cut-off current measurement .Automatic fail indicator of alarm lamp and buzzer.VFD display.Standard PLC interface .Option RS-232,RS-485
-
product
AC Ground Bond Tester
446
Our 446 model is a 4-in-1 tester with AC Hipot, DC Hipot, Insulation Resistance, and Ground Bond capabilities. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application. The 446 is equipped with multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Add to user safety by equipping your tester with Personal Protective Equipment (PPE) via the built-in safety interlock.
-
product
Insulation Resistance Meters
Scientific Mes-Technik Private Ltd
General purpose insulation resistance meterAnalog indicator, High measurement speedTest voltage range: 10 V to 500 VSuitable for Test capacitor insulation testEasy operation
-
product
Analogue (1kV below) Insulation Tester
2732 IN
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Two continuity test on "low ohms" : 3Ω & 500Ω.● Compact and lightweight.● AC voltmeter with linear scale up to 600 Vac.● 200mA continuity short circuit current.● 1mA test current on insulation test at nominal voltage.● Automatic discharge of capacitive and inductive circuit with charge stored in the circuit under test.● Live warning and display or external voltage presence.● Fuse, air gap, crowbar and overload protected.● On line battery monitoring shows if battery is ok.● Manual zero ohm adjustment.● Low battery consumption.● Mirror scale.● Push and turn locking switch for continuous and hand free testing.● Designed for meet international standards.● Supplied with high quality test leads.● BS 16 edition.
-
product
Insulation & Multifunction Tester (LCD Display)
1153 AI
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Automatic voltmeter AC/DC at Start/Reset.● Auto range● Auto off.● Battery test.● Battery test at switch ON/Reset.● Safety voltmeter before each test.● Auto discharge on all test and all ranges.● Leads Auto-Null key.● Test Auto-Stop.● Smart hold & stop on voltmeter ac/dc.● Ener-Save feature to extend battery life.● Continuity short circuit current > 220mA.● Continuity open circuit voltage of 5Vdc.● Nominal voltage @ 1mA on all insulation ranges.● Accept 8 rechargeable batteries or Alkaline of normal.● BS 16 edition.
-
product
Multifunction Meter for Electrical Installations
AMPI-530
Measurement of short-circuit loop ; Testing of differential, general and selective protections for differential current ; Measurement of insulation resistance ; Up to 10GΩ ; Voltages: 50 V, 100 V, 250 V, 500 V, 1000 V ; Measurement of earth resistance ; Bi-directional continuity test on PE cables, phase sequence ; Measurement and recording of voltage, frequency, alternating current, cosϕ, power, harmonics and THD
-
product
PAT and Installation Verification Unit
PowerCheck 1557
The PowerCheck 1557 is a comprehensive PAT and installation verification checkbox. It carries out ongoing performance checks to ensure accurate measurement between calibration intervals. Fully tests Earth Continuity, Insulation Resistance, RCD Trip Time, RCD Trip Current, Loop, PE Conductor Current, Touch Current and Flash tests.
-
product
Insulation Resistance Tester
WB2681A
• Insulation test voltages: DC250V、DC500V、DC1000V • Range of open-circuit voltage: ±10% rated voltage • Testing time: 3~99 seconds or controlled manually
-
product
Multifunction Instrument
COMBI521EV
COMBI521EV is the new HT instrument to perform verification and control of electric car charging stations (EVSE) safety according to IEC / EN 61851-1 and IEC / EN60364-7-722 standards. Being a combined verification instrument, COMBI521EV also carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
product
Partial Discharge Measurements
MPD 500
The MPD 500 simplifies routine factory partial discharge measurements for electrical insulation systems. Engineered with OMICRON's long time experience, the MPD 500 is optimized for routine tests in high throughput environments.
-
product
Safety Test Panel for Geyser
Electrical Safety is the most primary and essential product conformity requirement for any product that uses electricity. The clauses of safety testing of electrical products laid by worldwide agencies such as UL, CE, BIS, etc. are stringent. The products need to pass through tests such as the high voltage test, insulation resistance test, earth bond test, leakage current test and so on. And to conform to such tests, SCR Elektroniks have developed for the testing of Geyser. In addition to the conventional safety tests, test for performance is also included.
-
product
Digital (1kV up) H.V. Insulation Tester
6210A IN (Ranges: 0.5kV, 1kV, 2.5kV, 5kV)
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Four insulation test voltages.● Insulation resistance; auto ranging on all ranges.● Bargraph indicates test voltage; rise and decay can be observed during tests.● Visual and audible warning if external voltage is present.● Fully protected: crow bar.● Carry case.● EEPROM calibration.
-
product
Insulation Resistance Tester
M300RT
Performs DC insulation resistance test " detects up to 4000 megohms at 500 VDC " Tests in compliance with UL, VDE, IEC and MIL STD 202 test standards. IEEE-488 optional
-
product
Insulation & Multifunction Tester (LCD Display)
4153 IN
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Measures Insulation Resistance, voltage (AC-DC) measurements with automatic hold facility, diode, ohm, and continuity with a short circuit current of minimum 220mA.● Auto-off function.● Energy conservation feature.● Ener-Save™ limit the test duration to about 10 Seconds.● Quick Test and EnerSave™ are unique features. Both saves energy.● No moving parts. All calibration are saved internally in a non volatile memory.● Easy calibration at any facility around the world.● Operates with rechargeable batteries, alkaline or low cost general purpose batteries.● Low cost maintenance, calibration, and ownership.● Complies to all the latest regulations, including UK.
-
product
Lightning Impulse Voltage Generator Test Equipment
HTCJ-V / 170
Wuhan Huatian Electric Power Automation Co., Ltd.
Used for conducting impulse voltage tests of lightning impulse voltage full wave, lightning impulse voltage truncation wave and operating impulse voltage wave for power equipment, etc., to test insulation performance.
