Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Module Accessory Kit, Quantity 26, 4-40 x .375" Socket Head Cap Screws
510109301
Used with modules: 510104118 and 510108104.
-
product
Non-Linear Junction Detectors
ORION® HX Deluxe
The hand-held ORION HX Deluxe Non-Linear Junction Detector (NLJD) has interchangeable 2.4 GHz and 900 MHz antenna heads. The ORION HX Deluxe NLJD is used to sweep areas for electronic semi-conductor components. In this way, the ORION HX Deluxe NLJD detects and helps to locate hidden electronics or eavesdropping devices regardless of whether the electronic device is turned on.
-
product
Laser Head
5517EL
The Keysight 5517EL is used primarily in VME and PC based laser interferometer systems where the velocity of motion is faster, such as semiconductor lithography and flat panel applications. Please contact Keysight for custom requirements.
-
product
Handheld Humidity/Temp Hygrometer
625
The Model 625 is an ideal instrument for indoor air quality (IAQ) and indoor environmental quality (IEQ) measurements of temperature and humidity. The EdgeTech 625 temp/RH probe can be used two ways: use it as an integrated unit by attaching the probe head to the instrument or connect both parts via a cable. The clear back-lit display can be switched between relative humidity, wet bulb, and dew point at the touch of a button.
-
product
High Speed Cameras
TETHERED HEAD SERIES
The FASTCAM Multi is a unique high-speed camera system featuring two compact and lightweight, sealed camera heads tethered to a remote processor. Benefiting from a high light sensitivity sensor delivering 1.3 megapixel resolution at 4,800fps, built-in data acquisition and options for long duration direct-to-SSD recording with the additional of the optional FASTDRIVE, the FASTCAM Multi is truly innovative.
-
product
Kelvin Test Contactor/Probe Head
Gemini
At 3.22 mm test height, the Gemini™ Kelvin test contactor is an excellent all-around spring probe with low inductance, high bandwidth, and excellent current-carrying capacity. The device under test (DUT) side tip design accurately maintains its 100 µm spacing for the life of the probe. Customers report typical probe life of 500 k to 800 k package insertions, or over 2M touchdowns at wafer-level test. The offset tip allows manageable board layout with a board-side spacing of 0.4 mm.Gemini Kelvin probes and contactors provide a first-rate solution that effortlessly makes reliable, true Kelvin contact for high-volume final test of both singulated packages and wafer-level devices. Gemini Kelvin is an ideal solution for devices such as power controllers, A-D and D-A converters, power amplifiers and audio and video circuits.
-
product
Photometers
S 1000
Universal high-precision instruments for the measurement of illuminance E with system photometer heads for laboratory applications in automated measuring systems with computer control.
-
product
Measurement Front End of the ACQUAlab Generation
LabBGN
labBGN is the first of the new ACQUAlab generation of measurement front ends. It is used in conjunction with the background noise simulation systems 3PASS HAE-BGN/ HAE-car, the communication analysis system ACQUA and other HEAD acoustics components.
-
product
Constant Pressure Dual Head Pump
ReaXus HF Series
The HF Series pumps are specifically designed to meet the requirements of Preparative Liquid Chromatography (HPLC) and high pressure Process/Metering applications. The Stainless Steel fluid path will withstand the toughest applications.
-
product
LED Spot Type UV Curing Systems
AICURE UJ30/35
Panasonic Industrial Devices Sales Company of America
The compact UJ30/35 UV Curing System can be equipped with up to four individually controlled LED heads. Different types of UV-LED heads are available with an irradiation wavelength of either 365nm, 385nm or 405nm. The Controller allows for external contact inputs or PLCs for automated applications.
-
product
InGaAs Optical Power Head
81624C
The new 81624C optical power head provides a 5 mm detector area and allows flexible placement of the remote optical power meter, which is then connected to the N7749C. The 81624C accepts parallel beams with up to 4 mm diameter, standard SM fiber and MM fiber with max. 100 μm core diameter, NA ≤ 0.3. A wide choice of adapters allows input from popular fiber connector types, bare fibers or open beams. The magnetic D-shaped adapters allow rapid removal and replacement without twisting attached fibers.
-
product
Infrared Gas Detector
iTrans2
Teledyne Gas & Flame Detection
The iTrans2 infrared gas detector employs an intelligent electronics platform to provide one or two points of detection from a single head for maximum flexibility, superior performance and lower installation costs. With the optional HART Communication Protocol, the iTrans2 offers remote diagnostics, set-up or calibration by superimposing a high-frequency current across the industry standard 4-20mA analog line.
-
product
Encoder-Modulator
SFT3542HA
Hangzhou Softel Optic Co., Ltd.
SFT3542HA SD encoder modulator is a professional high integration device which includes encoding, multiplexing, scrambling and modulation. It supports 8 to 24 CVBS inputs, one DVB-C tuner input and 128 IP input with Data1 (GE) and Data2 (FE) port. It also supports DVB-C RF out with 4 adjacent carries, and supports Data1 (GE) output port to support 4 MPTS out. This full function device makes it ideal for small CATV head end system, and it’s a smart choice for hotel V system, entertainment system in sports bar, hospital, apartment…
-
product
Digital Tachometer
TAC-L
Model TAC-L Portable Digital Tachometer measures rotational speed either by contacting a rotatable head to the shaft of the object, or using photo sensor to detect the reflections from the laser. The laser target can record from a distance of up to 20 inches and gives a more accurate measurement than LED targeting. Model TAC-L includes a large LCD with a backlight for use in dark areas.
-
product
Compact Micro-size Inductive Proximity Sensor
GS
Panasonic Industrial Devices Sales Company of America
The Panasonic GS Compact Micro-size Inductive Proximity Sensor has Sensor heads that come in multiple sizes with a separate amplifier controller.
-
product
Firmware Engineering Projects
Precision Development Consulting Inc
Hand control module for teleprompter, Analog data acquisition and filtering, High-Power Arc Lamp Power Supply Controller and RTP gas flow and Vacuum System controller, Disk drive company test racks, Disk Drive Spindle Motor Tester, Disk Drive Head Stack Tester, Wafer photoresist coating and development system control PC boards, Nuclear Plant secondary water temperature monitor
-
product
AFM for Large Samples
NaniteAFM
The unparalleled small footprint of the NaniteAFM scan head and its highprecision/quick lock mounting system make it the ideal atomic force microscopefor integration into automated industrial environments. With a resolution below one nanometer, the NaniteAFM is capable of detecting and visualizing even the smallest surface structures.
-
product
Near-Field Probes 100 kHz up to 50 MHz
LF1 set
The LF1 near-field probe set consists of 4 shielded near-field probes used during the development process for emission measurement of longwave, medium wave, and shortwave frequencies on electronic devices. The probe heads of the LF1 set are designed for incremental detection of sources of electromagnetic interference on assemblies. First, the electromagnetic interference of the assembly is detected by the LF-R 400 probe from up to 10 cm. Then probes with higher resolution like the LF-B 3, LF-U 5 and LF-U 2.5 are used to more precisely detect any source of interference. The probe heads are designed for taking measurements at single pins and larger components. Near-field probes are small and handy. They have a current attenuating sheath and, therefore, are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. The H-field probes do not have an internal terminating resistance of 50 Ω.
-
product
MEMS-Scanner Evaluation-Kit
The "QSDrive Scan Kit" evaluation kit enables small and medium-sized companies in particular to operate ResoLin components from the Fraunhofer IPMS in accordance with the specifications without the time-consuming in-house development of control electronics. The evaluation kit consists of a ResoLin component – a cardanic MEMS scanner with a linear axis and an optional, orthogonally oriented resonant axis – and control electronics that enable the components to be operated with an optimized trajectory supplied. The component is held by a scan head, which is also included in the scope of delivery and which, thanks to its special construction, can easily be integrated into common optical test setups. Depending on the design of the MEMS component, controlled operation of the component and synchronized operation of the resonant axis are also possible. The function is controlled by software that communicates with the electronics via USB.
-
product
PDS Trailing Dredging Suction Hopper Software
PDS-TSHD
TELEDYNE PDS for Trailing Suction Hopper Dredge (TSHD) is designed to meet the dynamic demands of today’s dredge operator.TELEDYNE PDS-TSHD is an easy to use monitoring system that visualizes the dredge process real time in 3D, top, and profile views. The system gives an instant overview of the horizontal and vertical position of the suction tube, the vessel outline, and the dredge heads along with the surveyed depths, design, and dredged depth. Dredged areas are shown in various views, which are updated as soon as new data is available. Alarms can be generated for safety of the operation and to maintain the quality of the dredge progress.
-
product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
product
TrainLink™ Head Of Train Device
Wabtec Trainlink telemetry systems provide a critical link to last-car information, such as brake pipe pressure, motion status, battery condition, and high visibility marker status.
-
product
Emulation & Test Interface
Solder down modules to suit any package type provides a cost effective solution for replacement test heads, male or female. The mating top modules can incorporate either a ZIF or standard IC socket and the addition of optional test pins if required from RS Components.
-
product
Bench Type Panel Meter
ED-205
Standard Electric Works Co., Ltd
● Dimension：91(L) × 103(W) × 100(D)mm● Deflection Angle : 90°● Scale Length：Approx. 65mm ● Terminal： 4mm socket captive head, suitable for wire or pin-type test lead.● Material And Color： Acrylic resin meter cover, white scale plate, plastic stand in black.● Safety Standard： IEC/EN 61010-1 CAT Ⅱ 300V EN 61326-1 EN 61000-4-2 EN 61000-4-3
-
product
Final Test Manipulators
for test heads up to 250 kg / 550 lbsfinal test dedicatedhandler docking prolowest possible floor loadeasy motion in z-direction to facilitate docking processforce feedback control feature ensuring operator safety and protecting equipment during set-upactive cable managementdurable and robust designoptimized footprint for various test heads580 mm linear in/out motion for handler service access160 mm linear side-to-side feature270 column pivoting featurenumerous additional, unique features for individual set-up requirements
-
-
product
Separate Amplifier Pressure Sensor
AP-40 Series
Separate Amplifier Pressure Sensor. The industry's smallest and lightest air pressure sensor head, weighing only 7g. The super-small sensor head can be mounted close to the detection point decreasing response time.
-
product
USB Axis Module
E1735A
The E1735A USB Axis Module is the electronic interface for the 5519A/B laser head used in the Keysight 5530 Laser Calibration System. It also provides the interface for the 10888A remote control unit (optional) and the A-quad-B encoder input (optional).
-
product
÷10 HiZ 500 MHz Passive Probe for WaveSufer 400 Series Oscilloscopes.
PP007-WS-1
The PP007 embodies leading technology in passive probe design. The small probe is optimized for maximum waveform fidelity, including high frequency signal components, in a rugged probe suitable for every day.The sharp probe tip* is spring loaded, allowing it to retract into the narrow probe head. The tip does not slip off the object being probed—important when probing small geometry surface-mounted components. Probing dense circuits is easier with the small 2.5 mm ground sleeve, which provides much better visibility than 5 mm and 3.5 mm probes.
-
product
Micropositioner
XYZ 500 MIMT
Quarter Research and Development
Submicron manipulator and translation stage. The XYZ-500-MIMT Micropositioner is intended for precise probing and instrumentation for industrial, medical, biological, semiconductor, and general scientific applications. It provides 3-axis motion with .500" movement on each axis. Motion is controlled by three precision stepping motors attached to precision gear heads 64:1 (standard), that drive a 100 threads per inch screw (standard).
-
product
Saluki SE3001 Optical Chopper (1Hz - 10kHz)
SE3001 Optical Chopper is high-precision optical equipment with its chopper frequencies from 1 Hz to 10 kHz. With the advantage of PID technology and high-quality motor, the frequency accuracy of SE3001 is up to 0.5%. SE3001 consists of a console, a chopper head and a control line. The main function of the console is to control the speed of the motor to achieve the target speed. The chopper head is mainly composed of a base and a motor with a blade.
