Filter Results By:
Products
Applications
Manufacturers
- CAMI Research Inc.
product
Light-Guided Connector Assembly | Cable & Harness Tester
CableEye Light Director System
Our Light Director™ system (patented) provides a computer-guided technique for assembling connectors used in aerospace, medical, and other high-reliability applications. This system uses light fibers driven by super-bright LED lamps to individually illuminate target cavities in the connector being assembled. When the technician enters the wire code printed on unconnected wires, or touches a wire connected at the other end, the CableEye software turns on the appropriate fiber, thereby causing a bright, flashing light to project from inside the target cavity guiding the technician to the proper insertion point. Correct insertion is confirmed by the elimination of light from that location, whereas insertion into an incorrect location leaves the flashing light visible.
-
product
IEC60529 IPX34 Hand Held Spray Nozzle
IPX34
Shenzhen Chuangxin Instruments Co., Ltd.
The Spray Tester IPX 3/4 is a hand-held test device to verify protection against spraying and splashing water. The water pressure can be adjusted using the flow control knob on the device to give the required flow rate.
-
product
Firmware Engineering Projects
Precision Development Consulting Inc
Hand control module for teleprompter, Analog data acquisition and filtering, High-Power Arc Lamp Power Supply Controller and RTP gas flow and Vacuum System controller, Disk drive company test racks, Disk Drive Spindle Motor Tester, Disk Drive Head Stack Tester, Wafer photoresist coating and development system control PC boards, Nuclear Plant secondary water temperature monitor
-
product
Medical Masks Differential Pressure Tester
Sataton Instruments Technology CO., Ltd
Medical face mask differential pressure tester also called mask breathility tester is to determine the breathability of medical face mask materials. The tester can measure the differential pressure (Delta P) required to draw air through a measured surface area at a constant air flow rate is used to measure the air exchange pressure of the medical face mask materials. By providing the suction air through the holding sample, the tester can measure the Delta P by differential pressure transducer. It is to determine the air permeability and using comfort of the materials for medical mask.
-
product
Anemometer
Shenzhen UYIGAO Electronic Technology Co., Ltd
Digital Wind Speed Air Flow anemometer Temperature Meter Tester
-
product
Geotextile Water Permeability Tester
TG010
TESTEX Testing Equipment Systems Ltd.
Geotextile Water Permeability Tester, to determine the constant-head water flow capacity (water permeability) within the plane of a geotextile or geotextile-related product, is measured under varying normal compressive stresses, typical hydraulic gradients and defined contact surface.
-
product
Air Permeability Tester
TF164B
TESTEX Testing Equipment Systems Ltd.
Our Air Permeability Tester determines the resistance of fabrics (woven, knitted and non-woven textile materials) to the passage of air (air flow) under constant pre-set air pressure while firmly clamped in the test rig of selected test head/area.The specimen is loaded to the test area of the instrument easily by means of a pneumatic holder. By pressing down the holder to start the test. The air permeability tester is equipped with a vacuum pump to draw air through an automatic interchangeable test head with a circular opening. The pre-selected test pressure is automatically maintained, and after a few seconds the air permeability of the test specimen is digitally displayed in the pre-selected unit of measure on the touch panel after test the holder is released and the vacuum pump is shut off.
-
product
Melt Flow Index Testers
Instron® melt flow testers are specifically designed for easy and accurate measuring of Melt Flow Rate (MFR) and Melt Volume Rate (MVR). Our extrusion plastometers range from manual to semi-automated plastic melt flow index testers performing multiple weight tests. All our Melt Flow Index testing equipment meets the latest ASTM and ISO standards.
-
product
Bi-Directional Digital Hydraulic Testers
DHT401 Series
A simplified digital hydraulic tester with a single ON / OFF switch. Measure flow, temperature and pressure in one robust unit.
-
product
LED tester
Ecopia's LED tester is good to measure both electrical(I-V curve) and optical(Spectra, Light intensity) properties of LED chip, LED lamp, SMD type at the same time.It also makes it possible to see LED sample's construction , seeing through microscope. LED tester main body flow input current ,and emitted light from the LED sample is focused on lens of microscope.From this process, our LED tester can provide repeatable tested results and minimize error values and improve convenience of how to use.
-
product
Portable Hydraulic Testers
Flo-tech portable hydraulic testers simultaneously measure the flow rate, temperature and pressure of hydraulic fluid. Flow rates are derived from an internal turbine meter assembly. These units were designed for testing pumps, valves, cylinders, motors, hydrostatic or power shift transmissions and power steering systems in both mobile and stationary applications. When used in a preventive maintenance program, untimely or catastrophic repairs are minimized. Three families of testers are available to provide operators with the perfect solution that fits their needs, each quipped with a carrying handle to improve portability.
-
product
Loop Testing
Megger loop testers offer both traditional measuring techniques and state of the art “non-RCD Tripping” technology. Use these products to determine the prospective earth fault current, which is the maximum current able to flow in a phase-earth fault in an installation, and also to indicate the prospective short circuit current which is the maximum current able to flow in the event of a phase-neutral fault.
-
product
Oxidation Stability & Cold Flow Properties
These Anton Paar instruments enable you to evaluate the oxidation stability as well as the storage and thermal stability of mineral oil products or oil and fat containing cosmetics and food samples. The gum content tester is available for tests on the gum content of fuels and other volatile distillates. Cold flow properties (cold filter plugging point and cloud and pour point) show the lowest temperature for a trouble-free operation of diesel fuel or heating oil.
-
product
Oil Pour Point Tester
Weshine Electric Manufacturing Co., Ltd
WESHINE’s fully-integrated, automatic cloud and pour point apparatus(VS-9612 Cloud and Pour Point Tester) offers precise and convenient flow testing of petroleum products, biodiesel fuels, additives and lubricating oils.
-
product
Satellite ATE
MS 1123
Configurable Automatic Test Equipment (ATE) MKII is a customized tester, built to carry out card level testing for satellite systems (12 different types of boards). The purpose of ATE is to provide a user-friendly environment to test the boards for their functionality, perform specific tests of each card. The card level testing facilitates troubleshooting down to a faulty signal flow path. Both hardware and software designed such a way that each Input / Output is configurable and user can dynamically script the test procedure using standard ‘C’ Language.
-
product
For Overhead Distribution Line Current Tester With Power Flow Direction Record
MHR-600
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Measuring and recording the average current values & power flow directions in the setting interval.・Easy to use, as an indirect hot-line work tool.・Memorized data can be outputted to USB memoryafter measurement.・For 6.6KV circuit, protection level IP64.
-
product
Contact Resistance Tester
Weshine Electric Manufacturing Co., Ltd
The loop resistance tester is used to test the conductive loop resistance of various switchgear, and the test current shall not be less than 100A. Due to the oxidation of the contact surface, poor contact tightening and other reasons, the contact resistance increases. When a large current flows, the temperature of the contact point increases, which further accelerates the oxidation of the contact surface and further increases the contact resistance.
-
product
T8730 AIR FLOW TESTER UNIVERSAL
T8730 was designed for the precise task of measuring flows on parts such as filters (medicinal, diesel or petrol), tubes, nozzles, openings, valves, etc…Other than the classic flow measurement, the tool also has other ways of making it as versatile as possible in its category: ascent and descent ramps, opening tests and burst testing.Another separate function is the "continuous measurement", i.e. a test with infinite times allowing adjustment of the taps and part repairs in real time.The tool also avails of an intelligent pressure adjustment, which uses the automatic pressure regulator to continuously adjust the test pressure based on the variation in load loss, to ensure the reading is as stable and repetitive as possible.
-
product
CEAST VisualMELT Software
VisualMELT Software is designed to control all the functions of the Modular Melt Flow Systems, from single-weight to multiple-weight tests. The software enables the user to manage all optional equipment, including the load cell, the automatic cutting device, and the motorized weight lifter. When working with a multi-weight tester, it is possible to set up and control single-weight or multi-weight tests, as well as define the order and number of weights to be applied.
-
product
Melt Flow Testers
nstron®'s CEAST Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Flow Rate (MFR) and the Melt Volume Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests. Our testers meet ASTM and ISO standards.
-
product
Leak Masters
Uson provides automatic non-destructive air leak and flow measurement equipment and solutions used in product development and manufacturing environments for medical device, automotive, electric vehicle battery, packaging and industrial applications. Uson leak testers are highly configurable and are built with premium components ensuring maximum quality, reliability and performance.
-
product
Flow Leak Testers
If you need high-quality air flow testers, you’ve come to the right place. We carry equipment for mass flow and leak testing, laminar flow, and continuous flow. You have the option of choosing touch screen or standard digital. All our equipment is compact and includes high-performing, state-of-the-art technology. Begin testing your equipment with our premium-grade flow testing equipment. Explore our amazing selection of flow testing equipment.
-
product
Cabin Leakage Tester
The Kanomax Cabin Leakage Tester pressurizes or depressurizes the automobile vehicle cabin to measure the changes in cabin pressure. The control unit consists of a manometer and pressure transducers. The manometer detects the leakage flow, which is calculated by measuring the nozzle pressure relative to static pressure. The tester controls an adjustable fan to maintain static test pressure.
-
product
Face Masks Particulate Filtration Efficiency PFE Tester
GLE-20
GLE-20 is an oil-salt two-in-one Face Masks Particulate Filtration Efficiency PFE Tester. According to ASTM F1862-17, ASTM F2299-03 (2017), ASTM F2100-2019, BS EN14683-2019, BS EN 14387-2004+A1 2008, BS EN 136-1998, BS EN 140-1999, BS EN 143-2000 +C1-A1, BS EN 149-2001+A1, etc. It is used to test the particulate filtering efficiency of daily protective masks and medical masks, and to determine the obstruction performance of ordinary fabrics and medical protective masks against a constant flow of airflow.
-
product
Portable Small Meter Tester
The Portable Small Meter Tester (PSMT) is a lightweight system for field testing of 5/81 in. meters. It includes a test meter with control valves, hose connections, fittings and pressure gauge. Meter tests can be done without removing them from service. The inlet control valve ensures an accurate test start and stop. A globe valve downstream from the meter allows flow rate adjustment during test. Connection to the PSMT is made using standard 3/4 in. male hose connections located on the exterior of the case. Two 3/4 x 39 in. metal-reinforced flexible hoses are provided for easy field connections.
-
product
Volume Flow Rate & Velocity
Lutron Electronic Enterprise Co., Ltd.
Volume Flow Rate & Velocity Testers by Lutron
-
product
RCD Testers
PeakTech Prüf- und Messtechnik GmbH
The PeakTech 2710 is a residual current tester, which is used to determine tripping currents and the tripping times of residual current circuit breakers, which are used in every new building according to current building regulations. Residual current circuit breakers are used for personal protection and switch off a circuit when a residual current is registered which flows off via the protective earth (PE). RCD testers let a fault current flow and thus determine at which fault current the RCD triggers. The tripping time is also measured. These two parameters, tripping current and tripping time, are the safety-relevant parameters of an RCD. The various selectable test currents and characteristics that can be set with this device make the PeakTech 2710 the ideal companion for every electrician.
-
product
Primary Current Injection Testers
Primary Current Injection Tester is designed for testing protective relay and circuit breakers and also testing the turns ratio of current transformers at high variable currents. A test current is injected into the primary side of a system to determine how the system behaves at particular levels of current. This test makes it possible to determine whether the relay will trip and how long the current needs to flow before the trip is initiated.
-
product
Ground Earth Resistance Tester
2678X
Shenzhen Chuangxin Instruments Co., Ltd.
Ground Earth Resistance Tester verifies the integrity (continuity) of the protective bonding of the equipment (Class I equipment) designed to secure safety through the basic insulation and protective earthing. It is also called earth (ground) bonding test. If the continuity of the protective bonding is confirmed, we can conclude that the equipment has the requirements for preventing electric shock even if the insulation between the primary circuit and the accessible conductive section fails and a fault current flows through the distribution system.
-
product
Powder Rheometer
FT4
The FT4 Powder Rheometer® was designed with one purpose in mind - to characterise the rheology, or flow properties, of powders. This remains a primary function today, but the instrument, accessories and methodologies have been continuously developed to the point where the FT4 is now considered a universal powder tester.
-
product
Environmental Testers
Environmental testers sample and measure environmental elements such as temperature, humidity, sound, pH & air flow.
