Filter Results By:
Products
Applications
Manufacturers
Current Generators
Produce electric current.
- TEAM SOLUTIONS, INC.
product
8 SE Or 4 Diff. Input Channels, 4 Analog Current Output Channels, PCI Express
APCIE-3121-8-4C
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
product
Impuls Current Generator
Hilo-Test manufactures power generators for surge current material and safety tests, in particular for the examination of diverting elements such as gas discharge tubes, varistors, SPDs, and components in which such protective elements are installed, according to according to the IEC / EN 61643-11. Below you will find the right solution.
-
product
Electronic Loads
The DSO and DSOT series electronic loads are designed using advanced linear technology.The DSO series offers two main functions: constant current and constant resistance. However, these loads can absorb full power between 20% and 100% of the acceptable input voltage thanks to the autoranging mode.For more extensive requirements, we offer 'DSOT' models that also include constant voltage and constant power functions. These functions are essential for testing voltage generators such as automotive alternators or photovoltaic panels to determine their power curve. In addition, DSOT models have a basic '0 Volt' characteristic, which means they can be used with input voltages as low as 0 Volt. However, they still maintain a high reaction speed, which can reach 1V/us and 8A/us.
-
product
Current Differential Relay
SEL-587
Schweitzer Engineering Laboratories, Inc.
The SEL-587 Current Differential/Overcurrent Relay provides protection for any two-input apparatus, such as transformers, motors, generators, and reactors. Apply it for differential and overcurrent protection and use event reports for quick post-event analysis.
-
product
Resistors
A passive two-terminal electrical component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses. High-power resistors that can dissipate many watts of electrical power as heat may be used as part of motor controls, in power distribution systems, or as test loads for generators. Fixed resistors have resistances that only change slightly with temperature, time or operating voltage. Variable resistors can be used to adjust circuit elements (such as a volume control or a lamp dimmer), or as sensing devices for heat, light, humidity, force, or chemical activity.
-
product
Switch
TOE 9261
Toellner Electronic Instrumente GmbH
Input voltage 60 V, Output current up to 100 A, Rise / fall time < 500 ns, Short-circuit-proof, Switchable discharge of load circuit, Interruption in supply and ground lines up to 100 A, Switchable buffering of input circuit, 4 signal line switches, Control with any signal generators (TTL level)
-
product
High Current Generators
Quantum Composers is a recognized industry leader for Current Pulsers and Firesets. We specifically design our units for use in pyrotechnic applications such as Aerospace, Defense, Propulsion, and Automotive Safety and Squib testing. Our current generators are used throughout the world in demanding and harsh testing environments where quality, reliability, and safety are paramount. We are also an excellent replacement and upgrade solution for legacy equipment.
-
product
Waveform Amplifier
TS250
The TS250 Waveform Amplifier is a one of a king instrument perfect for amplifying signal generators. It is designed to amplify voltage, power or current for while driving heavy (low ohmic) loads. The TS250 offers eight voltage ranges to choose from ±10V to +65V. The TS250 output up to 6A peak current. To obtain higher current, parallel connect two or more TS250 in as shown in the Application Section.
-
product
HBM Verification Tester
HBM-VT
High Power Pulse Instruments GmbH
- HBM pulse generator verification tester according ANSI/ESDA/JEDEC JS-001 up to ±10kV- To be used in HBM test and qualification labs for regular pulse generator specification compliance test in order to fulfill lab audit and certification requirements- Fully automatic compliance test and verification of HBM pulse generators regarding ANSI/ESDA/JEDEC JS-001 normative standard at 3 different load conditions: Short Circuit, 500 Ω, and a reference diode at VBR=15 V reverse breakdown voltage, including DC test- Parameter evaluation and verification of the transient HBM current waveforms: Peak Current, Rise Time, Decay Time, Maximum Ringing Current- Optionally available upgrade for all HPPI TLP-3010C, 4010C, 8010A, 8010C, HBM-TS10-A hardware systems in combination with HBM-S1-B (6kV) pulse generators (upgrade on request)- Fully automatic test report generation (PDF)- Electrically floating (no fixed system ground): The HBM loads, current sensor output, USB control interface and the enclosure are electrically floating. There is no limiting system ground which may introduce common-mode interference induced HBM current measurement errors.- Isolated industrial full-speed USB control interface- Isolated power supply derived from USB port- Compact size 126mm x 82.5mm x 44.5mm
-
product
Inrush Current Generators for Zno Production Line
Shanghai Guantu Technology Co., Ltd.
Inrush Current Generator Standard: IEC61008, IEC61009, I61051/61643, ANSI C62.31, C62.33, C62.35, TU K20, K21, K44, K45, UL943Inrush Current Generator Features1. LCD screen display, built-in computer control, man-machine dialogue, easy to operate.2. Program-controlled high-voltage power supply, high voltage stability and precision3. Imported non-inductive high-power resistors are used to ensure the consistency of surge waveforms4. The main switch adopts electronic switch discharge mode, and the output polarity is automatically switched
-
product
Insulation Testers
Shenzhen UYIGAO Electronic Technology Co., Ltd
Insulation testers test for capacitance and current leakage in system cables, generators and motors, high voltage equipment and switchgears.
-
product
Motor/Generator Test Equipment
Winding ohmmeters RMO-M series measure winding resistance of inductive test objects such as electrical motors and generators. Motor test or generator test of winding resistance is especially important for early-stage failure detection.RMO-M series instruments generate true DC ripple-free current with automatically regulated measurement and discharge process. Even more, test instruments are portable and enclosed in a metal casing.Applications supported by DV Power motor/generator test equipment include:Winding resistance measurement of generators and electrical motorsResistance measurement of high-current bus bar jointsResistance measurement of cable splicesAll of the above-mentioned measurements are performed with the highest accuracy. The advanced DV-Win PC software enables collecting both numerical and graphical results. These features provide an easier and more efficient analysis. After the test, a DV-Win software generates a test report a single click. Finally, a user can easily customize the report and save it in different formats, such as XLS and PDF.
-
product
Pulse Adapter
CV30P650
Frothingham Electronics Corporation
The CV30 P650 test station is currently the highest voltage pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. The CV30 P650 pulse adapter can produce a maximum current of 100A at up to 600V using exponential pulses up the 10/1000 waveform. The pulser is rated at 30KW from 300V to 650V. Voltage compliance at 100A is 600V. The station can also include all of the usual FEC200 tests in the same test program.
-
product
AC Resonant Test System
Yangzhou Power Electric Co., Ltd
Testing of certain apparatus requires much high voltage or current that a straight AC test system is not sufficient. Thus resonant test reactor with a variable core is needed. The main advantage of such test systems is lower input power and larger output power. The resonant test system is designed to compensate capacitance in the testing circuit precisely by tuning inductance of the test system. AC resonant test system is used for factory testing of middle, high and ultra-high voltage cables, capacitors, generators, motors, power transformers and gas-insulated switchgears.
-
product
Signal Generator, 20MHz, 2 Channel
33510B
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
product
Pulse Adapter
CV30 P300
Frothingham Electronics Corporation
The CV30 P300 test station is the highest current 30KW pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. For exponential pulses up to the 10/1000, the station can produce 30KW, 1000A, or 300V whichever is the most limiting. The station can also include all of the usual FEC200 tests in the same test program.
-
product
Arbitrary Current Generator Family
PXA(e)73xx
The PXA(e)73xx ArbGen family features up to two simultaneously working channels with 100MS/s, 16Bit resolution and an output current up to 30mA in sink mode (at up to 30V) or ±20mA in combined source/sink mode (at up to ±10V).Every channel is equipped with 2MB memory. The whole amount of 1 million samples can be partitioned into one ore more waveform segments. Depending on the number of channels and the floating option, the Arbitrary Function Generators are built into a compact 3U PXI(e) device for 1 or 2 slots.
-
product
Earthing Resistance Tester
JYD-10A
transformer neutral grounding resistor is the vital need in medium voltage AC distribution network that are also called by different names like Neutral Earthling Resistors. They are taken into use to limit the current that would flow through the neutral point of a transformer or generator in the event of an earth fault. They are also used for resistance grounding of connected generators and transformers.
-
product
Power Amplifiers
Power Amplifier is used to amplify the output of the CS700A or CS701 signal generators. The 52 MHz bandwidth amplifier can swing 36Vpp with an output current up to 1A continuous. The CS1070 includes an internal inverting power supply to provide the negative rail, simplifying power supply requirements. The gain is fixed at x10 (20dB). The output voltage range is ±5V to ±18V and asymmetrical to +31, -5V for PSRR measurements right up to 30V as the input supply increases past 20V.
-
product
DC Hipot Test Set
KVZG
KV Hipot Power Test Equipment Co.,Ltd
DC Hipot Tester is applied to measure output voltage and leakage current for zinc oxide arresters, magnetic blowing arresters, power cables, generators, transformers, circuit breakers and other equipment.
-
product
"Stiff Grid" and Parallel Operation AC Generator Excitation Regulator
SVRFP
The Kinetics model SVRFP Exciter/Regulator rectifier is designed and rated in capacity and operating parameters for the application of exciting the fields on an AC generator in parallel with other AC generators and the power system is a "stiff system" in relation to loading. A "stiff system" is a generating system that is of sufficient capacity or the generator is "small" in relation to the system grid, that the AC system voltage under impulse/step loading condition does not require forcing of the generator field to maintain the power grid voltage. Systems are designed with a standard unit service factor to operate within the +10% to -20% nominal voltage rating at 100% current rating.
-
product
Automatic Relay Test Set
DRTS 33
DRTS 33 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 3 Voltage generators simultaneously available.
-
product
Impulse Generators and Measurement Systems
Designed to generate impulse voltages that simulate lightning strokes andswitching surges as defined by IEC, ANSI/IEEE, and other national standards on:• Distribution transformers• Small power transformers• Cables (type tests)• Arrestors (impulse current tests)• Motors / generatorsTesting ApplicationsImpulse Generators andMeasurement Systems• Insulators• Bushings• GIS• Instrument transformers
-
product
Generators
We offer a wide range of power supplies, current and voltage supplies, frequency references, RF generators, transceivers.
-
-
product
Signal Generator, 20MHz, 1 Channel, Arb.
33511B
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
product
Insulation Resistance Tester
Aarohi Embedded Systems Pvt. Ltd
Aarohi make device enable us to measure electrical leakage in wire, results are very reliable as we shall be passing electric current through device while we are testing. The equipment basically uses for verifying the electrical insulation level of any device such as motors, cables, generators, windings, etc.
-
product
Loading Rheostats (Resistive Load)
Supreme Instrument Laboratories
Loading Rheostat is a device specially designed to meet the requirements of Engineering Laboratories, Electrical Test Rooms and Industries. It is used for loading transformers, power generators, supply mains etc. neatly and efficiently. It can also be used advantageously for regulating current and adjusting voltage besides its application for calibrating meters and thus eliminating the need for graded rheostats.
-
product
Automatic Relay Test Set
DRTS 34
DRTS 34 is the most powerful diagnostic test set designed to perform accurate tests on protection relays, transducers, energy and power quality meters. This advanced test equipment is also thought to satisfy all the needs related to commissioning and substation maintenance. 3 Current and 4 Voltage generators simultaneously available.
-
product
High Current Sensor
HCS-BTA
Vernier Software & Technology, LLC
Use the High Current Sensor in experiments that involve currents larger than 1 A, such as solar panels, hand generators, and other alternative energy projects.
-
product
Motor Winding Ohmmeter
RMO-M Series
The motor/generator winding resistance test is used to identify open windings, shorts between two windings, short to grounds, connection mistakes or shorted turns. This non-invasive test of winding resistance helps to pinpoint problems regarding windings in stator or rotor part of an electrical machine. Additionally, motor winding ohmmeter has the capability of performing heat run test which will show a change in windings resistance with an increase of temperature.The RMO-M series is designed as an ideal aid in preventive maintenance of electrical motors and generators. They are powerful (up to 100A of test current), portable (8 kg) and generate DC current which is completely ripple-free. This makes measurement very precise with 0,1% accuracy.Three voltage channels make measurement very easy since it is possible to obtain a value of all three winding resistances in one measurement
