Filter Results By:
Products
Applications
Manufacturers
-
product
100MHz DDS Signal Generator
408A
The 408A generates cosine, sine and ACMOS/TTL outputs simultaneously and is programmable in 1µHz steps from 100Hz to 100MHz. It is also programmable for FSK and CHIRP outputs. The 408A is controlled by an RS232 serial interface. Phase can be programmed with 14-bit resolution.The Frequency is accurate to 1ppm when using the on board TCXO timebase or it can be factory configured to use an external frequency input as the timebase. A Line Voltage AC Adapter and a CD containing SOF8 windows softwareare included. A DDS8m is used inside the 408A.
-
product
PC/104 Single Board Computer with Vortex86DX3 System-on-Chip
CM1-86DX3
The CoreModule CM1-86DX3 is a PC/104 board with DMP Vortex86-DX3 single chip solution and has a very good performance to power ratio. The board comprises all peripherals needed for an embedded PC on a small 3.775" by 4.050" printed circuit board. The CM1-86DX3 integrates a powerful yet efficient DMP Vortex86DX3 with graphic controller and audio controller together with an additional GBit Ethernet controller to form a complete PC, with all the standard peripherals already onboard. Two Ethernet ports (1x GBit and 1x 100MBit), four RS232/RS422/RS485 serial ports, two USB 2.0 host controller to handle the communication with external devices. There are PS/2 connectors for keyboard and mouse. A first generation SATA interface allows the connection of hard disk or CD drive. CFast is also available. System expansion can easily be realized over the PC/104 bus connectors.
-
product
Social Engineering With Physical & Logical Attack
LGMS Security Team will approach the Social Engineering assessment as an intelligence operation. During the course of assessment, LGMS Security Team will base on clear objectives to breach the security controls using information that has been obtained through deception including phishing emails, sending of malicious parcels (CD or thumb-drives), and social engineering phone calls.
-
product
Non-booting System Diagnostics
BootPath Diagnostics
BootPath Diagnostics allow end users to troubleshoot systems that fail to boot into any operating system. BootPath Diagnostics are often integrated into the system ROM as a BIOS extension, making them available even when all storage devices are unavailable, and may also be used from a CD, USB drive, network location, or disk partition. This enables end users to better diagnose non-booting systems and provides savings in associated support and warranty costs.
-
product
Automated High-Resolution AOI Tool Modular Inspections
LIGHTiX
Next generation macro inspection system (AOI).• All-side wafer inspection: Front, back and edge inspection.• 100% defect images without throughput impact.• Integrated high-end microscope review.• True Color Inspection (TCI) technology.• Advanced CD, 2D/3D, OVL and EBR metrology.• Automatic defect classification• Best in class cost of ownership for high resolution AOI• High-speed patterned wafer inspection• High defect sensitivity• ISO Class 1 certified• Tool – to – tool matching
-
product
Spectrometers
MOS-500.
CD spectropolarimeter specifically optimized for both steady state and rapid kinetics applications. The CD spectrometer guarantees excellent performance: sensitivity, precision, speed and modularity from far-UV to NIR region.
-
product
Digital I/O Cards
104-DIO-48E
The circuits use an 82C55A PPI with mode 0 supported. Ports A, B and C are buffered with 74ABT245 transceivers and pulled up to 5V. The optional 82C54 has three-sixteen bit down-counters within one chip. These counters are useful for making frequency outputs, measuring frequency of square waves, pulse width outputs, pulse width measurements etc. Software drivers are provided on CD.
-
product
Common Metallic Pendulum Impact Testing Machine
JB-(C/D)
Jinan Testing Equipment IE Corporation
KB- (C/D) common type metallic pendulum impact testing system is the basic model for impact tester. The metallic pendulum impact tester is used to determine the impact resistance of metal materials under dynamic load and capable of doing a large number of impact tests continuously. The display method for the models is different, respectively there are analog dial display, touch screen digital display and computer display. For the later two models, it can display the impact power, impact toughness, and pendulum rotation angle. All the testing reports can be printed out. The metallic pendulum impact testing system is the essential quality control equipment for metal material manufacturers and QC departments, as well as the necessary instrument of research institutes for new material research.
-
product
Impedance Standards and Calibrators
Impedance Calibrator is to replace countless single value RCL standards with one calibrator that can switch between the standards like a CD changer in your car. The calibrator contains stable and temperature independent resistance standards, partial capacitance standards and partial inductance standards, simulated by RC T-type passive network. Calibration values of both complex parameters of partial standards are displayed on large LCD screen in preselected pairs of parameters as well as voltage, current and frequency readouts from built-in test signal meter. OPEN and SHORT reference positions are available as well.
-
product
Optical Chopper
These high stability variable frequency optical choppers each include a set of chemically blackened photoetched chopping discs. The mini chopper is an excellent choice for applications requiring a compact package. The chopping discs come in a variety of slot apertures and allow operation. Beam diameter is limited to 0.75mm when using the 200-slot disc and 1.0mm when using the 40 slot mini disc. The easy-to-interchange blades are made of non-magnetic, half hard brass and can be used in combination. Chopping frequency is set by adjusting a ten-turn dial or by applying an external DC voltage to the BNC input. Reference output is a TTL pulse and is in-phase with chopping action. The 5 digit led display gives a direct read-out of the chopping frequency. Power: 90-130V or 180-260V; 50/60Hz; 12VA max. Power supply included. Choppers are often used together with lock-in amplifiers.
-
product
Stamper Thickness Measurement Gauge
6360-HR-CD
The Model 6360-HR-CD Stamper Thickness Measurement System is a semi-automated thickness gauging platform and data analysis system for the measurement of optical media stampers. Patented non-contact capacitive sensors determine the stamper thickness without any damage to the stamper. A personal computer is provided to run the gauging platform, acquire measurement data and display results.
-
product
Interface Converter
ZET 7070
Basic delivery scope with digital transducers for laboratory use includes the following: interface converter ZET 7070, power supply module 220V→ +24V, measuring line connector ZET 7001 (these components are mounted on a din-rail 300 mm); cable USB 2.0 A→B – length 1,8 m; terminal resistance 120 Ohm (for industrial use — steel plug); CD with ZETLAB SENSOR software, enabling connection of up to 60 digital sensors; set of operational documentation.
-
product
PCI-104 8-Port, 4-port, And 2-port Multi-Protocol RS-232, RS-422, RS-485 Serial Communication Boards
104i-COM-8SM Family
The 104i-COM-8SM (PCI-104) family of multi-port, multi-protocol (RS-232, RS-422, RS-485), serial communication boards deliver up to eight high-speed serial communication ports for use in a wide variety of applications. The boards were developed for use by system integrators and manufacturers in the design of industrial and commercial systems. Based on the XR17D158, the boards have eight enhanced 16550 UARTs, each with a set of modem signals (CTS, RTS, RI, DTR, DSR, CD) in RS-232 mode. Each UART has both a 64 byte transmit and a 64 byte receive FIFO. Ports are accessed via two 40-pin IDC type right angle header connectors. 2 and 4-port versions are available, as well as RS-232 only models.
-
product
Small Drop Test System
KRD41 series
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
product
High Definition Audio Daughter Board with Line-in, Line-out and Mic-in
DB-Audio2
- Realtek ALC262 High Definition Audio codec- Three jacks: line-in, line-out and mic-in- 5x2 pin header for cable connection to external audio header on SBC- 4-pin header interface for CD audio output
-
product
6 Chip Detection and Burn Channels
CD1
The CD1 provides 6 Chip Detect and Fuzz Burn interface(s). A Chip Detector (CD) is a magnetic-electrical device that provides a reliable method of detecting impending failure of bearings and gears.
-
product
PC based USB Real Time Analyzer
1) Measurement microphone and its accessories (a windshield and a microphone clip)2) XLR-to-USB Converter3) USB cable (1.5 m) 4) CD (contains the copy-protected Multi-Instrument Software) 5) USB hardkey (contains a Multi-Instrument Standard License)6) Audio Test CD (contains a list of audio test tones and noises) (AudioTestCD.zip or AudioTestCD.rar)7) 1/8” TRS cable (1.8m) 8) Black Soft Pouch Case 9) Individual Sound Level Calibration Data 10) Individual Microphone Calibration Data (only provided in RTA-168B)11) A small microphone stand
-
product
Surface Analysis
InSight-450 3DAFM
Based on the production-proven InSight® 3DAFM platform for 300mm, the InSight-450 3DAFM is ideally suited for a broad range of roughness, depth and CD applications.
-
product
Environmental Testers
AEMC manufactures a line of cost effective, hand-held instruments for measuring temperature, humidity, light, wind speed and other variables. Each instrument in this series includes sensor, backlit CD and a shockproof holster. They are battery operated and can easily be carried in a shirt pocket.
-
product
2-MGEM Optical Anisotropy Factor Measurement System
The 2-MGEM Optical Anisotropy Factor Measurement System is a normal-incidence polarization reflection microscope designed to measure the sample Mueller matrix and is a 2008 R&D 100 Award Winner. This system is designed specifically to evaluate the Optical Anisotropy Factor (OPTAF) of cross sections of TRISO nuclear fuel pyrocarbon layers. Other possible material characterizations include measuring Mueller matrix elements of other crystals, carbon compounds, and thin film coatings (e.g. surfacedeposition films) at normal incidence. The 2-MGEM can also measure retardation (d), circular diattenuation (CD) and the polarization factor (ß). These parameters are not measurable using older techniques, since those techniques do not incorporate a compensating optical element.
-
product
Diaphragm Pressure Switch
CS & CD
Series CS and CD combine advanced design and precision construction in a small size. Unit is ideal for instrument panels, small compressors and general industrial applications. Visible set point and easy to wire SPDT snap switch reduce installation time. Operates in any position and is vibration resistant.
-
product
Electrical Receiver Conformance Test Application for IEEE 802.3bs/ cd
M8091BSCA
IEEE 802.3bs receiver test application for 200GAUI-4 and 400GAUI-8, covering chip-to-module, chip-to-chip, backplane, and copper cable interconnects.
-
product
Keysight N7800A Test Management Environment (TME) Software
Special recommended calibration options: The N7800A software calculates point-to-point ISO GUM measurement uncertainty. The special “H-series” calibration options in the link below provide lower measurement uncertainties through use of direct comparison to devices directly characterized by NPL or NIST (or another NMI), along with data on a CD for easy import into the N7800A (avoids manual entry). The overall resulting N7800A measurement uncertainty then incorporates this lower device uncertainty in the overall calculated uncertainty. For more information on the special options please view this spreadsheet N7800A Special Calibration Matrix.
-
product
SpectrOil M/F-W Fuel Analyzer
SpectrOil M
The SpectrOil M/F-W is a compact, rugged and easy to use fuel analysis spectrometer. It is designed specifically for the analysis of ash-forming contaminants in fuel such as sodium, potassium and vanadium that cause corrosion or deposits at turbine operating temperatures. It measures trace quantities of dissolved or suspended contaminant particles in a fuel sample using the time-tested and reliable rotating disc electrode (RDE) technique.
-
product
OMCD Version 4 Test Track CD For OmniMic V2
Designed for use with the Omnimic but is also useful as a standalone test CDGreat for setting amplifier gain levels19 test tracks
-
product
Virtual Interface Technology for 3D-IC Metrology
VIT
TSV profile (depth, top & bottom CD, tilt, SWA)-Residue Detection-RST-Copper Nail Height-Bump Height and Cu pillar height-Edge trim profile
-
product
Drag-and-Drop Protocol Software for Vision and CD Dissolution Testers
Protocol Manager™ Software
Teledyne LABS helps ensure the world’s pharmaceuticals are pure, safe, and effective by manufacturing instruments that set the global standard for quality, innovation, and long-term value. Software and software management play a large role in making sure those systems run as they should, and providing results that can be quickly analyzed and acted upon. Hanson software does so effectively and intuitively.Pharmaceutical research, manufacturing, and QC labs running Teledyne LABS Vision and/or CD14 dissolution testers can now manage users, methods, and instruments more efficiently than ever before. Our Protocol Manager software eliminates all instrument-based connectivity and storage limits by connecting your Hanson systems to a centralized protocol database on a Windows® client/server operating system. The spacious, easy-to-use, desktop interface provides drag-and-drop simplicity and increased support for 21 CFR Part 11 compliance.
-
product
GPIB Serial Interface
Model 4894B
* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals. * Expanded baud rate range from 50 to 115,200 baud.* 256 Kbyte RAM buffer for spooling data.* Over 600 Kbyte/second GPIB data transfer rate.*Transparent data transfer.* Programmable replacement for the NI CV interfaces.* 1 U high rack mount kit mounts one or two 4894Bs* Includes US 115 VAC Power Adapter, Manual and Support CD.
-
product
Dry Type Transformer Test
Wuhan Sangao Electrical Test Installations Limit Co.
GTB series dry testing transformer is adopted with new technology of winding epoxy vacuum pouring and CD type Iron core. Compared with similar product of oil immersed type transformer, it is light weight, smaller size, insulation strength and moisture-resistant is more improved.
-
product
Consumer Safety and RoHS Handheld XRF Analyzer
DELTA Consumer Safety & RoHS Handheld XRF Analyzers allow for testing large quantities of consumer & electronic products anywhere, anytime. Get simple, fast, nondestructive regulatory compliance screening for Pb, Cd, Hg, Br & more. Use for ASTM Method F2617-08, HR4040, CPSC, CPSIA & more.
