Filter Results By:
Products
Applications
Manufacturers
Hall
a measurable transverse voltage which occurs when current flows through a conductor in a magnetic field.
- Halls Instrumentation.
product
Light Testers
Hall’s have designed and manufactured products for oil, industrial, farming, commercial, and transportation markets. Products such as truck and trailer light testers, bop savers, early engine warning systems, oil spinners, engine control panels, dashes for service rigs, drillers panels, and sandline controls. Halls have been involved with over the rebuilding from scratch of over twenty service rigs.
-
product
Linear Hall Sensor
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
product
Hall Effect Sensors
906
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Bi-directional option 906B
-
product
CEMS
FMD 09
IMR Environmental Equipment, Inc.
The continuous measurement of velocity and temperature of gas flows is much important at operation of a system with flowing gases (e.g. hall outlet air, exhaust etc.).
-
product
Hall Motor Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable to no-load test and any DC motor with internal hall elements.
-
product
Gaussmeter
DX-102
DX-102 Gaussmeter is a portable gauss meter, based on the latest progress of Hall effect magnetic field measuring instrument, adopted DSP technology. Test probe adopts import GaAs linear Hall chip, the difference between any two probes is small, if damaged, it can be replaced directly. DX-102 Gaussmeter is an ideal DC magnetic field test instrument.
-
product
Resistivity and Hall Effect
The Resistivity System allows the user to make Resistivity and Hall Effect measurements in the range of to M. Samples are mounted on special platforms inside the VTI with contacts made to the sample according to the customer's requirements. Connections at the top of the probe are made via Fischer Connectors or Coaxial Cables. Keithley source and measurement electronics are provided with the system. These are fully controlled using the Measurement System Software.
-
product
Digital Gauss Meter
Digital Gauss meters are hand held devices which are used to measure D.C magnetic field using Hall Probes. The Gauss meter is available in two different ranges and helps in quick calibration. As the Digital Gauss meter is easy and simple to handle it is extensively used in industries which require measurement of magnetic field.
-
product
Position Sensors
Position sensor is a device that can detect the movement of an object and converts these into signals suitable for processing, transmission, or control. TE Connectivity (TE) is a leading manufacturer of industrial linear and angular position, tilt and fluid level sensors. Both off -the-shelf and custom position sensing solutions are available featuring our core technologies, including inductive, potentiometric, magnetoresistive, hall effect, reed switch, electrolytic and capacitive sensing.
-
product
Hall Effect Measurement System
RH 2010
The RH 2010 Hall Effect Measurement System has been designed for high flexibility and ease of use as a standard system for quick routine control measurements as well as for sophisticated temperature dependent Hall measurements for material research.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1000B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-1500B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Hall Effect Sensor
The hall effect sensor products are manufactured according to international standards. Being an ISO 9001:2008, ISO 14001 and OHSAS 18001 certified company, DER EE is capable of designing and producing superior products to the highest standards of customers' requirements. Hall effect sensors we provided are a device containing both the sensor which produces a very low signal level and contains the vacuum tube amplifier and a high gain integrated circuit (IC) amplifier in a single package. hall effect sensor offer many applications to sense position and motion, to control electric motor control, to sense wheel rotation and so on.
-
product
Reference Magnets
Reference Magnets provide a stable and convenient method to verify the accuracy and calibration of Hall Effect Gaussmeters, Teslameters, and Probes.
-
product
Group3 controllers
The Group3 controllers - the CNA and DNA - have a built-in PID algorithm, that allows them to perform local closed loop control. A controller, combined with a Group3 analog Hall probe forms a compact, inexpensive way to implement closed loop magnet control.
-
product
AC / DC Current Probe, 2 MHz, 500 Arms
N2780B
The N2780B current probe is an accurate and reliable solution for measuring AC and DC currents. Using a hybrid technology that includes a Hall effect sensor and an AC current transformer, the probe provides accurate measurement of DC or AC currents up to 500 Arms continuous.
-
product
Loudspeaker-Microphone Probe
Zircon
The Zircon is a loudspeaker-microphone probe for measuring in situ the absorption and reflection properties of surfaces. These may be indoor surfaces, such as in concert halls and gyms, or outdoor surfaces, such as road surfaces (ISO 13472-1), sound barriers installed in a free field (NF S 31-089) and traffic noise reducing devices (CEN/TS 1793-5)
-
-
product
Current Clamp Meter
CP 41
The CP 41 current clamp meter has been designed for reliable and accurate, non-intrusive measurement of AC, DC and complex waveform currents. Using advanced Hall Effect technology the CP 41 can measure currents accurately from 5mA to 40Amps.
-
product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-500B Open loop method
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
product
Hall Effect DC Current Sensor
CYHCT-L20K
ChenYang Technologies GmbH & Co. KG
The sensor CYHCT-L20K is based on open loop principle and designed with a high galvanic isolationbetween primary conductor and secondary circuit. It can be used for measurement of DC current, DCpulse currents etc. The output of the transducer reflects the real wave of the current carrying conductor.
-
product
Non-contacting Position Sensors
For use in harsh environments, Vishay offers non-contacting position sensors based on Hall Effect technology. Linear displacement, rotational (single- and multi-turn), and kit design options all provide a full 360° measurement range with no dead angles and very long life, since there is no wear and tear on sensor elements. Applications for Vishay’s non-contacting position sensors include any system where vibration, shock, or dithering is to be expected, such as embedded applications in vehicles.
-
product
SparkFun Current Sensor Breakout
ACS723 (Low Current)
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to moderate AC and DC current sensing applications. The ACS723 sensor uses a Hall effect sensor to output a voltage relative to the current flowing through the IP+ and IP- pins on the board. The advantage of using a Hall effect sensor, specifically, is that the circuit being sensed and the circuit reading the sensor are electrically isolated meaning that, although your Arduino is running on 5V, the sensed circuit can be operating at higher DC or AC voltages!
-
product
Hand-Held Gaussmeter
Model 907A/908A
The Model 907A and Model 908A Gaussmeters have been designed and manufactured with more than 30 years experience in magnetic measurement. This experience, along with our extensive knowledge of the magnetics market, has enabled us to offer an instrument incorporating all of the measurement functions a user is ever likely to need. The Model 907A & 908A are controlled by a simple menu and supplied with a thin, semi-flexible Transverse Hall Probe suitable for all but the very smallest of applications.
-
product
Open Loop Current Sensor
C03 50A
The C03 offers efficient and precise sensor solutions for direct, alternating and pulsed currents in systems for industry and commerce as well as in communication systems. It consists of three main components: an accurate, linear Hall sensor with low temperature drift, a flux collector and a transformer. It is characterized by a very low resistance and thus lowers power loss and temperature drift - for optimal performance.
-
product
Hall Effect Sensor
907 XP (Explosion Proof)
Features • NPN open collector, square-wave output • Zero speed operation with no signal loss • Non-contact, large gap distance sensing • Signal transmits up to 1,500 ft • Simple to install and set up • Powered by 5-24 VDC • Class I, Div I (D) Class II, Div I (E, F, G) Class III • XLB-3 enclosure • Bi-directional option (907B XP)
-
product
Measuring Device For Measuring Residual Magnetism
Teslameter M-Test LL
Measure residual magnetism on ferromagnetic materials precisely and reliablyquick detection of residual magnetismreproducible measurement results through automatic storage of the maximum valuesdefined measuring distance of 0.5 mm from the Hall probe to the measuring surfacemeasuring static and alternating magnetic fieldsselectable units: A / cm, Gauss, mTwear-resistant test sample
-
product
Closed Loop Hall Effect Current Sensors/Transducerswith Rectangle Windows
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on closed loop compensating principle and can be used formeasurement of DC and AC current, pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
-
product
Modular MAHA Universal Console
C_MCD | VP 186054
Maschinenbau Haldenwang GmbH & Co. KG.
The modular MAHA Universal Console can be expanded from a stand for the CONNECT analog display or a TFT television to a fully equipped input terminal. The mounting option of the C_MBT control cabinet allows free-standing installation and, thanks to the possibility of use in the emission tester and scissors lift area, also ensures a tidy and modern appearance in your workshop or test hall.
-
product
4-20mA Converters
4026
SPECTEC Innovative Sensor Solutions
Model 4026 Freq to Voltage or Freq to Current Converter accepts frequency input from any magnetic speed sensor, digital magnetic pickup or Hall effect zero speed sensors. Input and output configurations are field selectable. Input range is adjustable between 1100 Hz - 10 kHz or 75Hz to 1100 Hz. Output selection can be configured as 4-20mA converter, 10-50mA converter, 0-5 V FTV converter or 0-10 V FTV converter. ZERO and SPAN adjustments easily calibrate to almost any measurement range, with little interaction between the adjustments.
