Filter Results By:
Products
Applications
Manufacturers
- CAMI Research Inc.
product
Pin-Mapping for Custom Connectors, Test Fixtures, UUTs | Cable & Harness Testers
PinMap™
Check out this fast and super-easy pin-mapping process enabled by our optional CableEye® PinMap™ software. Map as fast as you can move the probe from one pin to the next. Use on your custom connectors, test fixtures, specially-built connector panels, or pigtail adapters to your CableEye tester. This software assigns test point numbers to connector types and applies standard pin designations to the pin numbers. For each custom connector, first choose a connector graphic from our large library to match your connector. Then touch the tester probe to the connector pins one-by-one to automatically detect and assign a test point to each pin. A synthetic voice reads probed pins as you touch them so you don’t need to take your eyes off the connector you’re probing. Finally, enter pin labels of your choice if you wish to override the standard designations.
-
product
Electrical Test Calibrators
The electrical test calibrators from Time Electronics are designed for rapid calibration of various electrical test equipment. Portable calibrators include the InsCal models for insulation tester calibration and the PatCal for calibration of portable appliance testers.
-
product
DC High Voltage Break Down Tester
High Voltage Breakdown Testers also known as Hipot Testers or Insulation Testers are a necessity for any Transformer testing, Substation equipment testing, Cable testing, Panel testing and testing of various insulating materials. Insulation testing is very important to ensure and maintain the safety of electrical equipments and also for the safety of operator.
-
product
Digital Insulation Tester
200M
Laxtronics Instruments & Controls Pvt. Ltd
Digital insulation tester Model No: DIT200M is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage from 1 to 30 Volts DC, its short circuit current is less than 100uA. The instrument can measure Resistance from 1 Meg Ohm to 1000 Meg Ohms.
-
product
6-24V Multi-functional Auto Tester With LED Display
6510A
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 6-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
product
IEC60068-2-75 Spring Hammer Test
CX-T03
Shenzhen Chuangxin Instruments Co., Ltd.
*Impact hammers are used to check the durability of enclosures for electrical appliances of other electronic products.If damage occurs from the Impact Hammer test .Accessibility probes can be used to measure the extent or severity of the damage.The Impact Hammer simulates the mechanical impact to which electrical equipment may be subjected. *This hammer is mainly used to test household and similar electrical appliances shell, lever, handle, knobs, lights and other shell to withstand mechanical shocks.* The impact tester made of stainless steel or alloy.
-
product
Electrical Tester
T5-600
The T5-600 Electrical Tester is a versatile troubleshooting tool you can carry to every job site. Use it to check voltage, continuity, and current, all with one compact, rugged tool. Just select volts, ohms, or current and the tester does the rest. For higher voltage applications check out the Fluke T5-1000.
-
product
Glow Plug Tester
The analyser test the condition of the glow plug in diesel engines and it comes with a graphical display without any language it shows the actual resistance of the glow plugs with conclusive result after the test. The analyser will switch off automatically if the tool is not being used, to conserve battery life. The tester comes with a built-in torch light to light-up dim surroundings for finding the glow plug or other car electrical problem.
-
product
Multi Trailer Tester Jobber Pack
#TSTPK1
Innovative Products of America
4 vehicle side trailer circuit testers and a three-way adapter.Test 7 flat, 7 round, 6 round and 4/5 pin trailers and receive a 3 way trailer adapter. Troubleshoot tractor trailer circuits Allows bypassing of troubled circuitry while on the road Eliminates guesswork "Winged" grip for easy removal from electrical connectorKit Includes:#7893: 7 Flat (Spade) Pin Trailer Circuit Tester#7865L: 7 Round Pin Circuit Tester (includes one brass jumper)#8000: 3 Way Trailer Adapter (7 flat pin to 6 round pin and 4/5 pin)#7897: 6 Round Pin Trailer Circuit Tester#7866: 4/5 Pin Harness Checker
-
product
Digital Ior Leakage Current Clamp Tester
MCL-400IR+
MULTI MEASURING INSTRUMENTS Co., Ltd.
・About Ior Leakage CurrentRecently, the leakage current clamp meter is widely used for insulation control of low voltage circuit as the supplementary method of the insulation resistance measurement. The control of leakage current has the advantages to enable the prediction of insulation condition in the electrical power line without having to shut off the power. The leakage current (Io) includes the capacitive leakage current (Ioc)originated in the capacitance and the resistive leakage current (Ior) originated in the insulation resistance each related to the ground. It is considered that the measurement of resistive leakage current (Ior) is the very useful and effective method for the insulation control of low voltage circuit. However, it was difficult to measure the resistive leakage current (Ior)with traditional leakage current clamp meter. MCL-400IR new digital clamp tester enabled the measurements of the resistive leakage current (Ior)without voltage input(phase detection).
-
product
Modular Test System
DMT
The DMT Tester is a modular test system that allows rapid measurement of electrical and non-electrical parameters of functional units. The system also allows basic ICT measurement with optional accessories. It is conceived as modular, with the possibility of integrating a wide range of own and external instruments. The DMT tester is controlled by its own SCADUS software.
-
product
Tester Electrical Interfaces
The primary element of the tester electrical interface is the Probe Pin Ring (PPR). Sometimes referred to as a ‘tower,’ this array of spring-loaded probes can be arranged to provide a controlled impedance path, a low leakage connection, a low inductance arrangement for high currents, or just about any connection characteristic you require. inTEST EMS provides electrical interfaces in various OEM-supported designs, inTEST standards, and custom configurations.
-
product
Pitot Static Tester
ADSE 746
The ADSE 746 caters fully for all aircraft types and the different electrical power supplies. It can be used for testing high performance civil and military aircraft, fixed and rotary wing. Themulti-pressure outlets option can suit themore complex pilot-staticsystems.This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The test set is robust and housed in a mobile weatherproof case fitted with tire wheels. An attached bag contains the pressure hoses and electrical cables.
-
product
Multi-function Tester
MFT5010
It can be used to test insulation resistance, continuity, loop impedance and RCCB, earth resistance tester, five major test requirement in the electrical testing industry. Phase indicator. Can check a wide range of 3-Phase Power source from 110V to 600V
-
product
Component Test
Our innovative multi-function Electrical Component Testers have advanced functions such as voltage power control feed to activate components like radiator fan, headlights, horn, actuators, etc. and the sensor simulator can provide simulation of voltage signals, frequencies, square waves & duty signals with varying intensity to test the feasibility of good sensor signals in comparison to bad ones when troubleshooting vehicle electrical faults.
-
product
12-24V Multi-functional Auto Tester With LCD Display
6511
Peaceful Thriving Enterprise Co Ltd
Test the automotive electrical system within 12-24V. In order to save the testing hours for the automotive electrical system, the tester is designed to test the system without re-connection between the vehicle battery and the testing components. For the testing and safety purpose, the tester contains short-circuit protection, which can also check the ground connection without voltage drop test. The short-circuit protection system contains the recoverable fuse, so the technician will not waste the fuses during the testing. The extension cable is long enough for a technician to test the whole system for the vehicle. Therefore, the technicians do not have to search for ground connection constantly.
-
product
Electrical Safety Testers
.AC/DC withstand voltage test & ground bond test .Insulation resistance test(ST60).Arc detection.Zero crossing turn-on,turn-off operation switch.Controllable ramp-up time .Ture RMS cut-off current measurement .Automatic fail indicator of alarm lamp and buzzer.VFD display.Standard PLC interface .Option RS-232,RS-485
-
product
Franklin Tester Model
Model FT2
Franklin Tester Model FT-2 is designed as per IS:649 & ASTM:717 Standard to measure insulation resistivity of electrical steel sheet. It requires precision & noise free DC regulated power supply and equally distributed pressure on electrode. Franklin Tester FT-2 regulated power supply provides 0.5000V with 0.1% accuracy over load and no load. Most of national and international standard has specified only 0.5%, means FT-2 is equipped with five time better accuracy than required.
-
product
Battery Conductance and Electrical System Tester
MDX-P300
The MDX-P300 is the first tester available from Midtronics which features an integrated printer allowing for immediate printing of test results. Now it is easier than ever to show thecurrent state of the battery and electrical system by providing customers with a printed result of the battery and system test. Using patented Conductance Technology, perform a quick, simple, and accurate battery or system test in seconds, and review the printout with the customer for added impact to preventive maintenance routines and customer service.
-
product
Current-Voltage Measurement System
Sciencetech''s IV Testers are electrical current-voltage measurement systems used to characterize photovoltaic cell performance. This current-voltage tester works by sampling various current versus voltage combinations of the photovoltaic cell with a variable impedence load.This IV Test system can measure electrical power from photovoltaic cells up to 20W. The voltage envelope is limited to 20V and the current to 1A. A higher power version, up to 60W, is available. In general, the limitation on this model is the 1A current limit: if your solar cell generates more than 1A, we recommend upgrading to the 60W version.
-
product
Hipot Tester
STM/L
SafeTest Manufacturing/Luminaire (STM/L) can be used as a simple manual electrical safety tester or with varying degrees of automatic test sequencing.
-
product
Automated Robust & Lightweight Installation Tester
EurotestAT
EurotestAT is automated robust and lightweight electrical installation tester. Experts from the field, maintenance people, inspectors and specialists help us ascend and descend the slopes with design and efficiency.
-
product
Network Tester
ZhangZhou Weihua Electronic co.,ltd
There is nothing worse than running your drops only to learn that you have a fault in one of the cable runs. Get it right the first time, get it right by choosing and using the right LAN Cable Testers. We offer a variety of cable testers, which are a must have to quickly and easily verify the integrity of Ethernet twisted pair cables. Our LAN testers will test twisted pair cables for open pairs, shorted pairs, reversed pairs, crossed pairs and split pairs. Network cable testers vary in complexity and price, but a basic tester consists of a source of electrical current and a measuring device. After that, cable testers vary in complexity and ability to do various testing.
-
product
Heavy Duty Circuit Tester
27000
Designed for testing electrical circuits and locating shorts, grounds, and open circuits. Electrical circuit tester available for checking 6V and 12V systems. Heavy duty battery clip .
-
product
Electrical Safety Tester
Basic testing methods of Glow wire device> and UL 746A, IEC829, DIN695, VDE0471, the Glow wire tester ZRS-3H/ZRS-3HS is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances. Adopting high-temperature coating spraying on steel structure and imported instrument display, with easy operation, stable performance the equipment is applicable to flame resistance tests of all levels of QC departments and corresponding enterprises.
-
product
Third Rail Voltage Tester
4E2-1
The Knopp 4E2-1 Voltage Tester is designed to detect electrical potential (voltage) between the third rail and ground on high voltage electrified transit systems. Two, redundant neon bulbs are used to indicate the presence of voltage. The prod handle and the tester housing are both made from moisture- and oil-resistant laminated phenolic. The prod tips are made from stainless steel. The tester housing includes a rubber hand guard to guide the operator in proper placement of his or her hand. There are no exposed metal parts other than to the two prod tips. All internal connections are soldered.
-
product
Drop Weight Impact Testing Machine
DWTT Series
Jinan Testing Equipment IE Corporation
DWTT Drop Weight Impact Testing System is suitable for drop weight tear test of various kinds of ferrite, especially for the test of DWTT for pipeline steel as ASTM-E 436, API-RP 5L3, ASTM-E 208 and DIN EN 10274. DWTT has integrated mechanical, electrical, and automatic control technology, and achieved full automation of feeding, hammer lifting impact, and fracture specimen collection. The load frame has a four-column design, features in stable supporting structure, rigid, dual sliding rails. The Drop Weight Drop Weight Tester is equipped with positioning mechanism, anti-dumping mechanism, safety mechanism, hydraulic buffer devices and security guard net. The impact energy is determined by the lifting height and configuration of different net weights. DWTT Drop Weight Impact Testing System is the essential quality control equipment for pipeline manufacturers, steel mills, iron and steel enterprises, and is also widely used for research institutes.1. Buffer device is equipped to avoid the second impact and absorb the residual energy after breaking the specimen so as to prevent the weigher and anvil from destroying. The installation of safety mechanism, buffer device, and security guard net will effectively secure the testing machine and its operation to extend its life.2. Configuration of the specimen-feeding system, anti-second impact device, and specimen centering mechanism will guarantee a quick, accurate and reliable test.
-
product
Automated Multi-Functional Tester
QTouch 1408 C
Qmax Test Technologies Pvt. Ltd.
QTouch 1408 C – Automated Multi-Functional Tester with in-built camera is designed to make automatic image capturing and probing of electrical signals with ease and speed especially in PCBs with high density/high pin count device that are mounted on the PCB. It is designed to move on X, Y, Z directions making it possible to probe every component as close as 20 mils. Easy tagging feature allows the user to get the real time XY coordinates using the library information with minimal intervention. CAD import feature is available for Auto Test Generation/to extract the XY coordinates from the CAD data. Qmax Automated Multi Functional Tester can perform Board level functional test of a PCB and guided probe / Back tracking diagnostics utility to reliably test Digital, Analog and Mixed Signal PCBs and fault isolation to the PCB level or component level.
-
product
Bonding Ohmeters
bonding ohmmeter is an affordable, highly accurate, and intrinsically safe electrical bond tester. This meter is capable of performing bond measurements on a variety of components and metal-to-metal connections. The 620LK has been independently UL-913 certified, ensuring quality and safety at each step of manufacturing. Due to its safety certifications and high level of accuracy, the 620LK meter is the choice bond tester for many commercial airliners, while its sibling the 620UK-B is in countless USAF programs.
-
product
Franklin Tester
Model 717
The Model 717 Franklin Tester provides a means of testing single strips or punchings of flat rolled electrical steel, for surface insulation resistance under predetermined conditions of voltage and pressure.
-
product
Glow Wire Test Apparatus
GLOW WIRE TESTER (also known as Glow Wire Test Apparatus) is designed to carry out fire hazard testing as specified in IEC 60695-2-10 2000-10. Flammability test is to check the ‘Resistance to Fire’ of electrical insulators that touch directly conducting parts & also parts of insulators. This test is also referred in many other standards such as IS 11000, IS 3854 : 1997 / IS 1293 :1988 / IS 371 :1999 & IS 11000 Pt 2 Sec 1, IEC 60335, IEC 884/94, IEC 60598, IEC 61058, BS 6458, BS EN 60695–2-10,11,12, etc.
