Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI/PXIe Wide Current Range Multiplexer Module, Quad 6-Channel, 1-Pole
42-514-106
The 40-514-106 (PXI) and 42-514-106 (PXIe) are low density multiplexers in quad 6-channel, 1-pole configuration. They are capable of switching a wide range of current, from 10 μA to 2.5 A at 220 VDC/250 VAC. The current capability of the module permits the use of a single module type for both low and medium current test applications.
-
product
Reference plus Comparator or Amplifier
Analog Devices reference plus comparator or amplifier products combine the excellent initial accuracy and low overtemperature drift performance of single function voltage references with comparators, buffer amplifiers, and current sense amplifiers. These products offer compact solutions for a broad range of applications such as battery monitoring, threshold detectors, window comparators, auto power-off circuits, and low dropout (LDO) regulators.
-
product
Signal Conditioning Instrumentation
Columbia Research Laboratories
Columbia offers a wide variety of Signal Conditioning Instrumentation for a variety of Sensor types. These range from Laboratory as well as Airborne Charge Amplifiers, Differential Charge Amplifiers, In-Line Charge Converters, Constant Current Power Supplies and ICP Compliant Amplifiers all in support of Columbia's extensive Piezoelectric product line. Additionally Columbia offers unique Strain Gage Instrumentation Amplifiers which provide built in auto zeroing of gage offset voltages which can increase typical measurement accuracies. These robust Signal Conditioning products have been flight qualified on many current military aircraft and missile programs and are now available for your distinctive program needs.
-
product
PXI Signal Amplifier
3180
Model 3180 was designed as a general purpose, wide band and high voltage amplifier, however, with specific applications in mind. It offers selectable gain of up to x50, with amplitudes of -90V to +90V and an output current of 150mA.
-
product
SQUID Series Arrays
The SQUID series arrays are ideal for readout of TES sensors or as amplifier stage for discrete two-stage applications. Integrated bias resistors for TES or two-stage applications reduce wiring complexity. Various arrays with input inductances of 3 to 6 nH, input sensitivities of 17 to 23 µA/Phi0, and a current noise between 5 and 10 pA/sqrt(Hz) @ 4 K are available.
-
product
Load Cell DIN Rail Signal Amplifier
LCD20
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
product
High-Voltage Power Amplifier / Piezo Driver
Model 2210
Trek’s Model 2210 is one of several models within our 2200-series of high-voltage 40 W amplifiers. Provided at an attractive price and offering high performance, the unit incorporates DC stability, wide bandwidth and well regulated/controlled AC output signals. It also features full four-quadrant class AB all-solid-state output stages, DC offset adjustment with front panel metering, and auto recovery shutdown to protect the output from being overpowered. The instrument stage sinks or sources current into reactive or resistive loads throughout the output voltage range making it ideal to achieve the accurate output response and high slew rates demanded by reactive loads.
-
product
Current Amplifiers
In order to achieve an extremely low noise performance very high gains were chosen, while nevertheless minimizing the associated bandwidth reduction.Thus, as a result of our sophisticated development efforts we can offer a professional "High-End" Current Amplifier line. The noise performance of our products surpasses by far that of conventionally designed OpAmp current-to-voltage converters at the corresponding bandwidth.
-
product
Current Source
M151
Clarke-Hess Communications Research
The Model M151 is a stable high current calibrator up to 120 A. Basic accuracy is 0.035 %. It can be controlled viaRS232 or GPIB interface. The Model 151 can function in a simulated amplifier mode to increase the current capabilityof any multifunction calibrator. It is suitable for power meter calibration because it can be synchronized with the inputsignal not only in amplitude but also in frequency and phase. The current terminals are isolated up to 450 Vpk againstcase (protective earth).
-
product
Gated Integrator | Boxcar Averager
GIA100
Artifex Engineering GmbH & Co. KG
The GIA100 gated integrator employs dual monolithic switched integrators. When paired with a photodiode, the boxcar amplifier measures the energy of single optical pulses. The GIA100 design results in very low leakage error, charge injection error and pickup. The precision input stage may be configured for current or voltage inputs.
-
product
High Voltage Power Amplifier
Model P0621N
Trek Model P0621N is a DC-stable, high-voltage power amplifier designed to provide precise control of output voltages in the range of 0 to +30 kV DC or peak AC, with an output current range of 0 to ±20 mA DC or peak AC. It is configured as a noninverting amplifier with fixed gains of 3000 V/V
-
product
LXI Low Thermal EMF Matrix 1-pole 44x33
60-510-021
The 60-510 is a high density 1-pole matrix module controlled via LXI. It has excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in ATE, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC micro-volt measurements. Ruthenium reed switches are used because of their good low level switching capability. They also have a very long life with excellent contact resistance stability, minimal wetting current and low thermal offset.
-
product
Potentiostat Galvanostat
EchemLab XM
EchemLab XM includes a reference grade potentiostat and frequency response analyzer (FRA). EchemLab XM has a built-in 100 V high voltage amplifier which can be used for not only for compliance measurements but also for high voltage cell polarization. This is useful in many high solution resistance applications, for example in organic electrochemistry. In addition to high voltage, power boosters can also be integrated to combine high current and high voltage in many specialized plating applications.
-
product
Waveform Amplifier
TS250
The TS250 Waveform Amplifier is a one of a king instrument perfect for amplifying signal generators. It is designed to amplify voltage, power or current for while driving heavy (low ohmic) loads. The TS250 offers eight voltage ranges to choose from ±10V to +65V. The TS250 output up to 6A peak current. To obtain higher current, parallel connect two or more TS250 in as shown in the Application Section.
-
product
Micropower Voltage References
Analog Devices offers a broad line precision micropower voltage references with extremely low quiescent currents (series references) or minimum shunt currents (shunt voltage references). All of our precision voltage references offer excellent initial accuracy and low temperature drift over time and temperature. Our Reference Plus products combine precision voltage references with comparators or amplifiers.
-
product
MOSFET Drivers
Renesas' product portfolio includes MOSFET gate drivers for 3-phase motor applications. The drivers have built-in detection/protection functions and are suitable for inverter driver applications such as EGR, HVAC and EPS. Line up the products with LDOs for MCU, 24V battery system capability, built-in current sense amplifiers, and motor angle detection function. The products support unit downsizing and high performance.
-
product
High-Voltage Power Amplifier
Model 40/15
The Model 40/15 is a DC-stable, high-voltage power amplifier featuring an all solid-state design for high slewrate, wide bandwidth, and low-noise operation. It is configured as noninverting with a fixed gain of 4000 V/V and is protected against overvoltage and overcurrent conditions that may be generated by active loads or by output short circuits to ground. Precision voltage and current monitors provide low-voltage representations of the high-voltage output and load current for monitoring purposes or for use as feedback signals in a closed-loop system.
-
product
High-Sensitivity Tri-Axial Accelerometer with Built-In Preamplifier
NP-7310
NP-7310 is the accelerometer with built-in preamplifier, and capable of tri–axial directions simultaneous measurement. It is suitable for the low frequency vibration measurement such as ground vibration or floor vibration while operating the machine. NP-7310 can be used with the sensor amplifier unit such as AU-2100, AU-2300 or PS-1300. Also, it is possible to input directly to the analyzer or recorder which the constant current amplifier is built-in such as the FFT Analyzer of DS-2000 series, DS-3000 series, CF-7200A, CF-9000 series or CF-3650/3850 series.
-
product
O/E Converter
TIA-4000
The TIA-4000 is comprised of a fibre coupled InGaAs APD detector combined with a variable reverse bias voltage network and fast transimpedance amplifier. The output of the unit is brought out to a type K female SMA connector. Light falling on the detector generates a positive-going proportional current. This current, multiplied by the transimpedance produces a voltage that is proportional to the light incident on the detector surface.
-
product
Current Amplifier/Generator
ULCA-1
The Ultrastable Low-noise Current Amplifier ULCA-1 is designed to fulfill the needs of high-accuracy low-current generation and measurements in the range from 1 fA to 1 µA (licensed by PTB).
-
product
Current Feedback Op Amplifiers
Analog Devices high speed (> 50 MHz) current feedback op amps enable you to operate at higher speeds. Current feedback op amps traditionally have wider bandwidths and higher slew rates than voltage feedback amplifiers and do not feature a gain bandwidth restriction associated with voltage feedback op amps.
-
product
Operational Amplifiers
Operational amplifiers from ams are ideally suited to audio applications. These CMOS devices are available as single, quad or differential amps. They feature good common-mode rejection, have low input bias currents, good gain bandwidth, low total harmonic distortion and an excellent rail-to-rail output-drive capability of 200mA peak.
-
product
High-Voltage Power Amplifier
623B
The Trek Model 623B DC-stable high-voltage power amplifier is designed to provide precise control of bi-polar output voltages in the range of 0 to ±2 kV DC or peak AC with an output current capability of ±40 mA DC or peak AC
-
product
Micro probes 1 MHz up to 6 GHz
MFA 01 set
The micro probes are used to measure magnetic fields and they have a high resolution. They measure magnetic fields up to 6 GHz, e.g. at signal conductors (150µm), SMD components (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the Bias tee BT 706. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee BT 706 to a spectrum analyzer or an oscilloscope. Langer EMV-Technik GmbH includes correction lines in the delivery. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
product
Isolation Amplifier Analog Output
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a high-accuracy D/A converter on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
product
Portable Power Amplifier
PA30Bip
PA30Bip portable power amplifier is designed with linear amplifier principle. It is very light portable solution with three channels of current output and four channels of voltage output.
-
product
Operational Amplifier
Op Amp Series
The amplifier is capable of operating at supply voltages from 0.9V to 3V with specified specs at 1V and 1.8V single supply.The input common mode range extends to both power supply rails without the offset glitch and input bias current phase reversal inherent to most rail to rail input amplifiers.
-
product
Logarithmic Transimpedance Amplifiers
Analog Devices translinear logarithmic amplifiers utilize advanced translinear techniques to provide an exceptionally large dynamic range in a versatile and easily used form. Our portfolio relies on proprietary innovations in design and precision laser trimming to achieve the wide measurement range and accuracy in products such as the AD8304 and AD8305. ADI translinear logarithmic amps are used in a variety of applications including optical power measurement, wide range baseband logarithmic compression, the measurement of current and voltage ratios, and optical absorbance measurements.
-
product
High-Speed High-Voltage Power Amplifier
Model 10/40A-HS
The Model 10/40A-HS is a DC-stable, high-speed, high-voltage power amplifier used in industrial and research applications. It features an all-solid-state design for high slew rate, wide bandwidth and low-noise operation. The four-quadrant, active output stage sinks or sources current into reactive or resistive loads throughout the output voltage range. This type of output is essential to achieve an accurate output response and high slew rate demanded by a variety of loads such as highly capacitive or reactive loads. It is configured as a non-inverting amplifier.
-
product
2-Quadrant Source/Measure Unit for Functional Test, 20 V, 1 A or 6 V, 3 A, 20 W
N6782A
The Keysight N6782A is a source/measure unit (SMU) designed specifically for advanced functional testing of a device. The ability to modulate the output up to 100 kHz along with capability to source and sink current (2-quadrant operation) makes the N6782A a perfect fit for advanced functional test of a variety of devices such as DC/DC converters, power management units, power amplifiers, and power management ICs. The input stage of the DUT can be stimulated by the fast sourcing and waveform capabilities. While the output stage can be loaded down and measured with the electronic load capabilities, providing a total test solution.
-
product
Broadband Power Amplifier
PAS-00210-80
* Solid State Power Amplifier* Small Signal Gain: 50 dB typ.* Rack Mount Case* Internal Cooling Fans* Type N Connectors* Over-voltage, over-current protections* Microprocessor controlled (optional)* Current monitor (optional)* Ethernet interface (optional)* Variable Gain (optional)* ALC power control (optional)
