Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Mini Coax, Contact, Receiver, two .025" Square Wire Wrap Posts
610104140
Mini Coax, Contact, Receiver, two .025" Square Wire Wrap Posts
-
product
Pulse Delay Generators
Quantum Composers provides innovation and value to our customers with our diverse family of Precision Pulse Generators. A wide range of pulse generator technology has been created to fit the needs of any budget and application. Our square wave signal generators provide a cost-effective method to create and synchronize multiple sequences, delayed triggering, or any precisely timed series of events.
-
product
Component Test
Our innovative multi-function Electrical Component Testers have advanced functions such as voltage power control feed to activate components like radiator fan, headlights, horn, actuators, etc. and the sensor simulator can provide simulation of voltage signals, frequencies, square waves & duty signals with varying intensity to test the feasibility of good sensor signals in comparison to bad ones when troubleshooting vehicle electrical faults.
-
product
10MHz DDS Sine & Square Wave SIGNAL GENERATOR
SG-10
Model SG-10 architecture is based on the latest advances in DDS technology. Microprocessor control delivers clean and accurate DC to 10MHz waveforms with frequency accuracy of 0.02% and 0.1 Hz frequency resolution.
-
product
Shock Test Systems
Sanwood Environmental Chambers Co ., Ltd.
Is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.
-
product
Digital I/O Cards
104-DIO-48E
The circuits use an 82C55A PPI with mode 0 supported. Ports A, B and C are buffered with 74ABT245 transceivers and pulled up to 5V. The optional 82C54 has three-sixteen bit down-counters within one chip. These counters are useful for making frequency outputs, measuring frequency of square waves, pulse width outputs, pulse width measurements etc. Software drivers are provided on CD.
-
product
Digital Combo Set for Measuring Low-Frequency Signals
SVG-5
- Measurement of root-mean-square AC voltage and frequency of single-ended or differential signals- Measurement of AC voltage frequency of single-ended or differential signals- Generation of sine waves- Visual examination of freeform signals- Signal spectrum analysis
-
product
Compact Multi-use Type Rotary Encoder
RP-432Z
Compact and economical design for general purpose;ideal for OEM applications5 VDC or 12 VDC operationEasy-to-use output signal connector2-phase and zero mark square wave outputsNine output pulse types to select from.
-
product
Variable Tone Generator
> 60 Hz to 18 kHz approx> 1.3 VAC P/P> Frequency & Level Pots> Sine or Square Wave> 4.5 x 2.5 x 1.1 inches> 9 volt battery operation
-
product
6U PXI Multi-Channel Analog I/O PXI Card
GX3348 Series
The GX3348 is a multi-channel analog I/O 6U PXI card which provides (3) programmable sources, a ground source connection, a pulse / square wave generator (A version only) and a 4 x 48 or 4 x 64 matrix - allowing the user to route the 3 sources, or ground to any of the 48 or 64 I/O channels. In addition, each I/O channel can be connected to a 16-bit A to D converter, providing DC voltage measurement capability for each channel. The module also offers (8) static digital I/O for controlling / monitoring a UUT's digital signals.
-
product
Utilities
Audio signal generator that include sine waves, square waves, white noise, and pink noise. The noise signals may be octave-band limited. In landscape mode, you can set sweep start and stop frequencies, and a time in seconds.
-
product
RF Proximity Detector
Type RPD-2 AND Type RPD-2A
The Type RPD-2 Radio Frequency (RF) Proximity Detector is designed to detect and locate devices that radiate radio waves in the high frequency to low microwave frequency range. Such devices often include surveillance and “spy” equipment. The Type RPD-2, when used with the different sensors, will detect the emanation of the radio wave within a confined area, and then isolate its location to within approximately a square foot. The type RPD-2A may be used as an RF field strength indicator for antenna field strength measurements. The RPD-2A is identical in function except that the meter scale is calibrated in relative dB units.
-
product
Oscillators for Radio Amateurs
An oscillator is an electronic circuit designed to produce either audio or radio frequency signals. These will generally have sineusoidal wave form, but other wave shapes such as square and sawtooth are possible. In radio equipment oscillators will always have a low output power, and if a radio frequency is produced, the oscillator is acually a basic radio transmitter.
-
product
EVISION Obstacle Detector
MS 1528
Obstacle Detector is a distance-measuring system based on ultrasonic sound utilizing the LPC2364FBD100. The system transmits a burst of ultrasonic sound waves towards the subject and then receives the corresponding echo. The LPC2364FBD100 integrated analog comparator is used to detect the arrival of the echo to the system. The time taken for the ultrasonic burst to travel the distance from the system to the subject and back to the system is accurately measured by the LPC2364FBD100. Assuming the speed of sound in air at room temperature to be 1100 ft/s, the LPC2364FBD100 computes the distance between the system and the subject and gives the information to buzzer. The minimum distance that this system can measure is eight inches and is limited by the transmitter’s transducer settling-time. The maximum distance that can be measured is 2 meter. The amplitude of the echo depends on the reflecting material, shape, and size. Sound-absorbing targets such as carpets and reflecting surfaces less than two square feet in area reflect poorly. The maximum measurable range is lower for such subjects. If the amplitude of the echo received by the system is so low that it is not detectable by the Comparator. This system is mainly used to replace normal sticks for the visually impaired (blind) peoples. This unit has standard USB 2.0 for mobile interface and has android application for user interface
-
product
SINE (Sinusoidal) Targets & Arrays
Sinusoidal Target Arrays have been recognized as a superior test method for a variety of applications, from moiré contouring to reliable MTF Evaluation of materials, lenses, cameras, and electro-optical systems (Follow the hyperlink to learn about using Sinusoids for MTF eval). Sinusoidal Pattern Arrays are manufactured on two different materials for both reflective and transmissive applications. Because of the inherent limitations of reflective materials, the maximum spatial frequency of the reflective pattern arrays is limited to 20 cycles per mm, while the transmission film arrays are offered in various sizes up to 256 cycles per mm. In addition, the sinusoidal arrays are available in a Single Frequency Grating or with Multi-Frequency Gratings. If instead of continuous sinusoidal frequency, you are looking for a square wave frequency design, then look to the Ronchi Gratings page. Should you need to alter the size of the pattern or the substrate, fill out our Custom Test Targets and Charts form and start the conversation.
-
product
Light-to-Frequency
Light-to-Frequency (LTF) sensors convert measurements of light intensity to a digital form for direct interfacing to a microcontroller. The output of the device is a square wave or pulse stream the frequency of which is linearly proportional to the light intensity. LTF converters are designed for applications such as ambient light measurement, light absorption/reflection in products such as white goods, photographic equipment, colorimetry, chemical analyzers and display contrast controls. They may be used in any system that requires a wide dynamic range, and/or high resolution digital measurement of light intensity.
-
product
AC Electronic Load
The electronic AC loads cover a wide variety of different voltage, current and power ranges. All the AC loads are programmed with 11 different sine, square and DC waves. With 5 crest factor variations of each, a total of 55 waveforms are available. An external input is also provided to enable the user to amplify signals from a waveform generator.AC Loads allow real world operating conditions to be simulated. Typical applications include circuit breaker, transformer & UPS output testing along with general laboratory and research work.
-
product
Loss Tangent M in Dielectric Oil
TAND220A
The measuring instrument type TAND220A complies with the international standard IEC 61620. The instrument is based on the so-called "low-amplitude, low-frequency alternating current square wave method" and allows accurate measurements of conductivity and relative permittivity. Conductivity measurement in the range of 0.01 pS/m to 20,000 pS/m allows the use of this instrument for quality control of high resistivity liquids even at room temperature. The TAND220A works with a low test voltage and also with a low test current so that it does not represent a danger for the operators.
-
product
Paddle Wheel Flow Sensor
FSP
Chuan Sheng Electronics Co., Ltd.
FSP - Paddle Wheel Flow Sensor, Using SUS and corrosion-resistant materials and design oxidation resistance, good stability and high resolution built-magnet rotor, NPN pulse square wave can be connected directly to the PLC / IPC IPC, the product is easy to maintain, easy to operate.
-
product
Mini Digital Multimeter
HH2103
Basic Accuracy 1.0%. LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A. Resistance test up to 2000KΩ. Diode test. Square Wave Signal Injection
-
product
HV Test bench
It is a deeply customizable test bench which is suitable to generate frequency and amplitude controlled voltage. This test bench could be used for life test or quality test on samples or devices. It can be configured both for sinusoidal test (STANDARD version) and both for square wave or pulse test (TechSQUARE). It includes safety systems for avoiding overload and incorrect use.
-
product
Phase Splitter Comb Generator
*Differential output - can also provide single ended outputs, one with positive going pulse, the second with negative going pulse. * Pulse height adjustable +1 to +5V peak into 50 ohms, on positive output, with concurrent -1 to -5V peak on negative output * Produces differential pulse on positive edge of input clock * Input clock may be 20-100MHz sinewave or 0.5-100MHz square wave, producing comb to 4GHz. Usable energy to >10GHz. * Differential outputs are designed to drive matched 50 ohm loads, but can drive any load, including short, without damage. Has integral fan. * Power Requirements: -12V @ 120mA and +18V @ 90mA.
-
product
Right Angle Waveguide to Coax Adapters
Fairview Microwave right angle waveguide to coax adapters include millimeter wave frequency ranges with models in the K-band (18 to 26.5 GHz) up to the V-band (50 to 65 GHz). These right angle waveguide to coax adapters offer excellent VSWR as low as 1.29:1, while also providing insertion loss performance as low as 0.3 dB. Waveguide sizes available for these new 90 degree coaxial adapter models include WR-42, WR-28, WR-22, WR-19 and WR-15. These coax to waveguide adapters in a right angle design are ideal for numerous applications requiring a transition from coaxial cable to waveguide or vice versa, including SATCOM, wireless communications, industrial, test and measurement and defense systems. Fairview’s new waveguide to coax adapter products feature a right-angle configuration, those with 2.92mm connectors use a UG-style square waveguide flange, 2.4mm and 1.85mm connector versions use a UG-style circular waveguide flange. Both male and female connector options are available in each right angle waveguide to coax adapter frequency band.
-
product
Palm Size Digital Multimeter, Calibrated, 1999 Count, Mean Value, Manual Range, 3.5 Digit
72-7770 CAL D
The 72-7770 CAL D from Tenma is a palm sized digital multimeter with 3 3/4 digit LCD. It is 3 1/2digits with steady operations, fashionable design and highly reliable hand held measuring instrument. The meter measures AC/DC voltage, AC/DC current, resistance, temperature, diode and continuity. It is an ideal tool for maintenance. The multimeter features square wave output, data hold, low battery indicator and display backlight, This meter complies with the standards CE, IEC61010, in pollution degree 2, overvoltage category (CAT I 600V, CAT II 300V) and double insulation.
-
product
High Voltage Power Supplies
The mains voltage (230V / 3 x 400V) is transformed, rectified and filtered by the HN series. The direct current output voltage is tuned by a variable transformer or regulated by a thyristor controller. With the HS and HV series the rectified mains voltage is supplied to a frequency converter, which produces a mid-frequency square wave voltage. This transformed, rectified and filtered alternating current produces the desired voltage as output, which is regulated by means of frequency variation or pulse width modulation. The equipment in the HV series supply, in addition to the high voltage output, up to 3 auxiliary outputs which can be used to supply e.g. heating, grid voltage or surge voltage.
-
product
Demonstration Board
SAMPULSE20x2
The SAMPULSE20x2 is a demonstration board for the Furaxa SiGe3 30GHz sampler/pulser IC. The SIGe3 IC is a dual channel sampler pulser chip, and the SAMPULSE20x2 demonstration board contains two 2.4mm combined TDR input/output connectors, one to each sampler/pulser channel in the IC. The SiGe3 IC's two sampler outputs are then sent to to two SMA jacks, the first outputting the sample taken on the rising edge of the sampler clock, and the second containing the sample taken on the falling edge of the sampler clock. The sampler clock input, which must be a square wave, may be set to any frequency from 5MHz to 1GHz, causing the board take two pairs of samples (one on each clock edge) at rates from 5 million to 1 billion per second. A pulser clock input, which may be set to any frequency from 5MHz to 2GHz, and MUST be a square wave (preferably differential) with rise time under 100pS, causes the board to produce concurrent pulses on both of the SiGe3's I/O pins, which produce near-concurrent pulses at the two 2.4mm sampler/pulser TDR input/output connectors.
-
product
Positive Displacement (PD) Meters
Positive Displacement (PD) flow meters are volumetric flow measurement instruments ideal for low flow rates, highly viscous fluids, and measurement of flows involving starts and stops or pulsing. Positive displacement flow meters are similar in design to the gear pump. The principle of operation is reversed however; instead of the gears driving the fluid, the fluid drives the gears. A non-intrusive hall-effect sensor detects the movement of the gear and as each gear tooth passes the sensor, a square wave pulse is produced and a discrete volume of liquid is measured. The resulting pulse train is proportional to the actual flow rate and provides a highly accurate representation of the fluid flow.
-
product
D/A, Arbitrary Waveform Generators
The Arbitrary Waveform Generator (AWG) is a powerful and flexible signal generator capable of outputting any wave shape within the bandwidth of the generator.Every AWG provides the ability to use it as a simple function generator. This allows creation and output of sine, rectangular (square), triangle, saw tooth, and DC waveforms directly without any complex operations.Details on the generation of Waveform can be found in separate articles:
-
product
Quasi Square Wave Constant Voltage Transformers
Osborne Quasi Square Wave Constant Voltage Transformers are used to regulate output voltages for applications that have varying input voltages. When used with a rectifier conversion circuit, these units provide an elegant design approach to voltage regulation. Osborne achieves this innovative approach by partnering the constant voltage transformer with an auxiliary resonant capacitor winding. The result is a unique (though time honored) technology that offers reliability, performance, and cost advantages over other styles of voltage regulation.
-
product
Function Generators
Waveform : Sine, Triangle, Square, Pulse, Sawtooth, Ramp 0.2Hz-150MHz EXT Frequency Counter(Option : 1:6 GHz or 2.7GHz) Self made insert ASIC Function : Total, RPM, Period, LPF, COUPL(AC/DC), ATT(X10) Fast,High-Resolution, 8Digits LED display Internal or External AM,FM Modulation Internal or External Burst and Linear Sweep Countrol from 1 : 1 to 100:1 TTL/CMOS Leveled Square Wave Output Maximum Attenuation of 20 dB cna be obtained Output impedance : 50 INPUT SENSITMTYKHz Range : 100mVms, MHz Range : 300mVms SWEEP WIDTH : Variable from 1:1 -100:1 RATE : 0.5Hz - 50Hz(20ms-2s) INTERNAL : Linear Bilt-in 5digits Green LED display
-
product
Single-Channel DC Powered Carrier Demodulator
CD16
The CD16 Miniature Carrier Demodulator is designed to deliver a 0 to 5 Vdc output from a variable reluctance transducer and operate from unregulated 9 to 55 Vdc power. A square wave excitation of 5 kHz is furnished to the transducer and the solid state integrated circuit amplifier and demodulator converts the transducer signal to an analog dc output. Zero and Span adjustments are made through access holes in the case.
