Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
product
Synchro to Digital-Resolver to Digital Converters
SACP-RACP
Computer Conversions Corporation
Computer Conversions Synchro-Resolver to ACP/ARP Converters accept choice of synchro-resolver input options, power input, and mounting configuration, converts synchro/resolver input into ACP (Azimuth Change Pulse) and ARP(Azimuth Reference Pulse) type outputs suitable for 75 ohm drive.
-
product
Digital to Synchro-Digital to Resolver Converters
ST-DRL ST-DSL ST Prefix
Computer Conversions Corporation
Terminations subject to converter module features where applicable.Plastic backplane mount track included, or may be mounted using spacers at mounting hole locations.
-
product
Synchro to Digital-Resolver to Digital Converters
MRDC
Computer Conversions Corporation
Computer Conversions’ MRDC64-3 is a miniature single chip solution for providing a complete 1 x 64 speed resolver interface into any demanding industrial or military application.
-
product
Synchro to Digital-Resolver to Digital Converters
MSI MRI MX
Computer Conversions Corporation
Computer Conversions MX Series are low cost multiplexed synchro or resolver to digital converter sets designed for Military or Industrial diagnostic and control applicatioms requiring 3-128 axis per control.
-
product
1, 2, or 3 Channels @ 0.5 VA, 1.5 VA or 3.0 VA
DSx
Synchros are transformer-type voltage/current transducers that convert a shaft or other rotating device's angular position and/or velocity to a multi-wire AC electrical signal. Both deliver signals proportional to the Sine and/or Cosine of the shaft angle. A Digital-to-Synchro simulator is used to convert digital angle/velocity commands to corresponding Synchro/Resolver AC signals.
-
product
Synchro to Digital and Resolver to Digital Converters
Computer Conversions Corporation
Resolution: Up to 20 Bit Single-speed Resolution, Up to 24 Bits Multi-Speed Multi-Turn Resolution.Accuracy: +/- 7 to +/-19 arc seconds 20 bit, +/-40 arc seconds 16 bit, +/- 1',+/-2.3 and +/-4' Reference Inputs: 2- 11.8V 26/ 115Vrms L-L 47 to 10,000 Hz. Isolated to > 500VDCSignal Inputs: 2 - 11.8, 26, 40, 90V.L-L. Isolated to . 500VDC.Options: Multispeed synchro input and bus card interface.
-
product
Synchro to Digital-Resolver to Digital Converters
SDT RDT
Computer Conversions Corporation
The SDT/RDT Series, are single module, tracking, Multi-speed synchro/resolver to digital converters designed for Military and Industrial Applications. They will accept Electrical Multi-speed, or Geared (dual speed) Multi-turn; Synchro or Resolver input sets (Fine/ Coarse), having the most standard ratio’s, and convert them into a single non-ambiguous 16 Bit data word with up to +/-20 arc. seconds accuracy.
-
product
Digital Synchro and Digital to Resolver
DSN-DRN
Computer Conversions Corporation
The DSN - DRN Series are highly reliable, miniature, narrow profile and low cost, continuously updating Digital Synchro and Digital to Resolver (AC Sine / Cosine) Converters designed for military and industrial control applications.
-
product
Embedded Synchro - Resolver -
LVDT I/O Cards
Computer Conversions Corporation
100% Transformer Isolation is offered for all AC I/O, and various Isolated DC converters are available as standard product, eliminating concerns for ground-loops, ground interjected (intermittent and ghostly) field noise, inductive surges, differing potentials, and high voltage field transients from effecting the card itself, the sensitive ISA bus backplane and any other device or system sharing these signals.
-
product
Synchro to Digital-Resolver to Digital Converters
SDC-F-RDC-F
Computer Conversions Corporation
SDC/RDC-F Series are Industry Standard Tracking Synchro and Resolver to Digital Converter modules with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command.
-
product
synchro or resolver to digital (BCD) converters
AIT
Computer Conversions Corporation
The TSb series are miniature, high performance continuous tracking synchro or resolver to digital (BCD) converters and angle indicators employing a type 2 servo loop, designed for military and industrial control applications. They will accept any 3 wire synchro or 4 wire resolver input over a frequency range of 50 to 1200Hz. and convert it into 0 to 359.9 degrees or +/-179.9 degrees, TTL compatible BCD data.
-
product
DC-Angle to Synchro or Resolver Converters
LDS & LDR
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
product
Synchro & Resolver Buffer Amplifiers
RPMA - SPMA
Computer Conversions Corporation
The SPMA/RPMA Series are low cost solid state synchro and resolver buffer amplifiers, isolators and format converters packaged in industry standard 2.6 x 3.1" modules for printed circuit card mount.
-
product
Synchro to Digital-Resolver to Digital Converters
HRDCK-HSDCK
Computer Conversions Corporation
HSDCK and HRDCK series are the highest accuracy, miniature tracking synchro and resolver to digital converters in the marketplace. They are designed specifically for ultra precise requirements in the most demanding industrial and military applications.
-
product
Digital to Synchro Converter
DSPH
Computer Conversions Corporation
The DSPH Series High Power Digital to Synchro Converters, are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and Radar/Antenna related, applications. They are commonly used on synchro based data transmission, retransmission, simulation, and instantaneous absolute position indicating and active control systems.
-
product
Digital to Synchro Converters
DSP
Computer Conversions Corporation
The DSP Series are high efficiency, AC Reference powered, Transformer Isolated, continuously updating “whole” Digital to Synchro Converters, designed for high performance Military and Industrial applications.
-
product
Digital to Synchro and Digital to Resolver Converters
Computer Conversions Corporation
1.2VA, 1.5VA, 4.5VA and 5VA Models60 or 400, & 60 and 400 Hz. Models to 22 KHz.Trouble Free Isolated Reference Inputs & Signal OutputsUltra High Efficiency, Low DistortionSelf Powered off the AC Reference Input (DSP Series)Internal Cool AC-Pulsating Supplies (DSP Series)Very Low Loss & Heat DissipationFULLY INTEGRATED, NO EXTERNAL COMPONENTS REQUIREDVery High Resistance to Shock and VibrationHigh Reliability Throughout ImplementationIsolated, Transient, Therrnally & Short Circuit Protected Outputs
-
product
Digital Synchro and Digital to Resolver
DSL- DRL
Computer Conversions Corporation
The DSL - DRL Series are highly reliable, miniature, low profile and low cost, continuously updating Digital Synchro and Digital to Resolver (AC Sine / Cosine) Converters designed for military and industrial control applications.
-
product
Synchro Differential Control Transmitter and Resolver Differential Control
SCDX-RCDX Series
Computer Conversions Corporation
The SCDX Series are low cost, miniature, solid state control differential transmitters and resolver transmitters designed for military and industrial control applications. They will directly replace electro-mechanical control differential transmitters (CDX) & thus provide digital control to existing analog servo systems.
-
product
Simulators
In-Phase Technologies simulators are designed to simulate our customer’s operating product, allowing them to perform testing and “what if” scenarios
-
product
DC to Synchro and Linear DC to Resolver Converters
ST-LDS & ST-LDR
Computer Conversions Corporation
ST-LDS and ST-LDR Prefix - Linear DC to Synchro and Linear DC to Resolver Converters On PCB with Mounting Track having Screw-Terminal Block for ease of wiring
-
product
Resolver to Digital and Digital to Resolver Converter
DP-VME-5031
DP-VME-5031 is a Resolver to Digital and Digital to Resolver Converter module. This module has four resolver to digital converters as measurement channels and six digital to resolver converters as stimulus channels.
-
product
ESD Simulators
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
-
product
ECU Simulators
Easily configurable and customizable ECU solutions. Perfect for use as gateway nodes, simulators, automated testers, and ECU replacements.
-
product
Satellite Simulators
Satellite Simulators enable RF testing of mobile satellite communication systems without the need of cabling and gives a loop-back test for Satcom terminals without the need to access the satellite.
-
product
Resolver to DC Sine / Cosine or Synchro to DC
ST-RD & ST-SD
Computer Conversions Corporation
ST-RD and ST-SD Series - Resolver to DC Sine / Cosine or Synchro to DC Sine Cosine Packaged on PCB with Track and Terminal Block and On-Board AC Reference Supply may be used driving DC Servo amp in active position synchronizing applications
-
product
Synchro And Resolver Angle Position Indicator
AP-501
The AP-501 is a high accuracy, auto-ranging, broad band synchro and resolver angle position indicator. The synchro or resolver angle is displayed on a bright 0.56 inch LED display. The indicator maintains a accuracy up 0.03 degrees even with synchro or resolver phase shifts up to 45 degrees over a frequency range of 47-300 Hz. The 800B301 is a low profile rack mounted synchro/resolver angle position indicator with 360 degree offset capability via front panel thumb wheel switches.
-
product
Temperature Simulators
A single select button scrolls quickly between the 3 factory set calibration points for efficiency. Two models to choose from: 271-018 (0°F, 32°F, 212°F) and 271-019 (32°F, 212°F, 500°F). Each unit includes a 3-point UKAS Accredited Calibration Certificate so you know that you''re using a precision instrument. Also included is a 3 foot type K test lead for connecting up your type K meters. You get precision at an economic price. Simple and fast!
-
product
Motor and Resolver Control
With excellent radiation tolerance and enhanced performance, CAES’ Motor and Resolver Control products are ideal for moving you through space and other harsh environments.
