Filter Results By:
Products
Applications
Manufacturers
CATV Signal Level Meters
measure decible level of electronic signal to assure TV picture quality.
See Also: Signal Level Meters, Satellite Signal Level Meters
- Virginia Panel Corporation
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 22-24 AWG
610138109
Primary mating contact 610138216. (May mate with other ITA contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2-ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.24
-
product
Radio Vector Tester
Wuhan Sunma Technology Co., Ltd.
Radio & Vector Network Analyzer adopts the advanced digital and RF combination design technology, fundamental wave frequency mixing technology, digital IF processing technology, intelligent power management technology, etc. It comes with features of high precision, small size, light weight, battery power, can measure SWR, Return Loss, Cable Loss, Impedance, DTF, etc, is used to the field test of cable, feeder, and the reflection parameters test of RF components in science and teaching. SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers.
-
product
Signal Level Meter
HT828B
Hangzhou Softel Optic Co., Ltd.
The signal level meter, SE828C is able to measure EQ, C/N, V/A and trunk volt in the CATV analog system, the number keys is designed to direct input frequency so that work would be easier. It can measure 2 channels at the same time.
-
product
Other CATV Meters
Wuhan Sunma Technology Co., Ltd.
SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers. also you can find other more equipment in CATV / Broadcasting fileds, such as Three Frequency Points, HFC Return Path Signal Generator, Return Path Signal Generator, Digital RF Signal Generator and so on.
-
product
Handheld Signal Level Meter, CATV
CT-SLM870
Handheld signal level meter, reads CATV 2-136 and Off-Air 2-69 by channel or by frequency
-
product
Signal Level Meters
Wuhan Sunma Technology Co., Ltd.
Signal Level Meter is specially designed and manufactured for CATV system installation and testing. It‘s a portable instrument, easy to carry with many functions.It can test CATV signal level both at channel and frequency mode. Also it can measure CATV TILT,C/N, trunk cable Voltage, ect. The big character TN LCD clear1y displays all testing results. It especia1ly fit for CATV station as a professional measurement instrument. it can display 2 channels at the same time.
-
product
Signal Level Meters
GAOTek offers a wide range of high performance and inexpensive TV and CATV signal level strength meters. TV signal strength meters and testers are required when installing or maintaining analog TV and digital TV systems and closed CCTV systems. The devices can effectively and accurately measure the analog channels and digital channels signal strength and are the preferred choice of TV installation technicians.
-
product
Satellite Meters
Wuhan Sunma Technology Co., Ltd.
Satellite Meter is a dedicated instrument for the direct version of the program using ST-Tech, integrated market-seeking Satellite, launched digital search Satellite.Satellite lock accurate, not false positives or missing signals, just listen to the sound of a few seconds can rapidly lock signal frequency. SunmaFiber provide all kinds of CATV meters, such as Signal Level Meter, QAM Analyzer, Spectrum Analyzer, DVB/DVC/DVT Analyzer and other TV testers.
-
product
Signal Level Meter
T1125
Hangzhou Softel Optic Co., Ltd.
The signal level meter, SE828C is able to measure EQ, C/N, V/A and trunk volt in the CATV analog system, the number keys is designed to direct input frequency so that work would be easier. It can measure 2 channels at the same time.
-
product
Analog Optical Power Meter - PXI
Power 1500 Series
The Power 1500 Series analog power meter brings cost-effective test and measurement. The Power 1500 provides logarithmic analog output as well as a digital optical power meter for applications that require real-time feedback.
-
product
Inline Optical Power Meter - PXI
Power 1600 Series
Quantifi Photonics’ Power 1600 Series inline optical power meters provides quick and accurate inline power monitoring. Seamlessly integrate the power meter into your new or existing PXI test setup and save space, lower your costs and improve testing efficiency.
-
product
Signal, Patchcord, ITA, 72", QuadraPaddle, 22 AWG White, Single Ended ( 5 Amps)
7-121922000-072
Signal, Patchcord, ITA, 72", QuadraPaddle, 22 AWG White, Single Ended ( 5 Amps).
-
product
Digital Power Meter
Digital Power Meter is designed for single-phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits, the 66200 uses state-of-the-art DSP digitizing technology.
-
product
3GHz 16-Channel Signal Generator 19" 3U Rack Module
LS30816R
The LS30816R, 3GHz 16 channel RF Analog Signal Generator, offers industry leading performance, in a 3U, 19” space efficient, rack-mounted box. The LS30816R features 16 phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. With the highest channel density in the market the LS30816R offer the ideal solution for applications requiring high channel count at minimum space and cost.
-
product
PXI Breadboard Module, 2-Slot, 15-Pin D-Type
40-220A-602
Versatile PXI Breadboard with 65 sq cm (10 sq in) of Prototype Area, fitted with 15-pin D-type connector, dual PXI slot width.
-
product
"Smart" Dynamic Signal Analyzers
EMX-4xxx
The EMX-4xxx product family contains high-performance breakout boxes (EMX-4008 and EMX-4016), smart high density dynamic signal analyzers (EMX-4250 and EMX-4251), smart PXIe 625 KSA/s 4-channel digizers (EMX-4350), and charge and IEPE PXIe 625 KSA/s 4-channel digitizers (EMX-4380).
-
product
PXIe-2515, 35-Channel, 0.25 A PXI Signal Insertion Switch Module
780587-15
PXIe, 35-Channel, 0.25 A PXI Signal Insertion Switch Module—The PXIe‑2515 is a multiplexer switch module that enables connectivity by routing high-speed digital I/O (DIO) signals between a device under test (DUT) and an NI high-speed DIO device or a parametric measurement device. You can use modules such as PXI Source Measure Units (SMUs) and PXI Digital Multimeters (DMMs) with high-speed digital devices. With the PXIe‑2515, you can perform parametric tests on digital pins without external connectivity or impedance mismatch challenges.
-
product
PXI Breadboard Module, 1-Slot, 96-Pin Micro-D
40-220A-001
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
CXA-m PXIe Signal Analyzer
M9290A
Deploy a smaller microwave footprint, no trade-off in precision: Rely on fully specified performance up to 26.5 GHz in 4 slots Optimize your balance between speed, sensitivity and accuracy with the choice to operate in swept or FFT modes Perform fast calibrated stimulus response measurement with full-band tracking generator Smooth the transition between R&D, manufacturing, and maintenance: CXA-m is code compatible with benchtop X-Series signal analyzers and ESA spectrum analyzers
-
product
PXIe-5668, Up to 26.5 GHz PXI Vector Signal Analyzer
783124-01
Up to 26.5 GHz PXI Vector Signal Analyzer - The PXIe‑5668 offers wide bandwidth with high-performance measurement performance and speed. It meets the challenging requirements of applications such as wireless communications, radio frequency integrated circuit characterization, RADAR test, and spectrum monitoring and signal intelligence. With its implementation as a PXI instrument, the PXIe‑5668 also features the fast measurement speed required for high-volume manufacturing test, and multi-instrument synchronization capabilities for phase-coherent MIMO test. You can use the optionally included PXIe-5698 preamplifier to improve dynamic range and sensitivity near the instrument noise floor.
-
product
PXIe-5665, Up to 14 GHz PXI Vector Signal Analyzer
781426-02
Up to 14 GHz PXI Vector Signal Analyzer - The PXIe‑5665 is a modular, three‑stage superheterodyne analyzer that you can use as either a spectrum analyzer or vector signal analyzer. It supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. In addition, you can use the PXIe‑5665 with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5665 can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5665 provides a low-cost solution to high-performance RF measurements.
-
product
PXI Breadboard Module, 2-Slot, 20-Pin GMCT
40-220A-802
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
product
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG White, Single Ended (3 Amps)
7-121924000-036
Signal, Patchcord, ITA, 36", QuadraPaddle, 24 AWG White, Single Ended (3 Amps).
-
product
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White Twisted Pair, Single Ended ( 5 Amps)
7-104422000-036
Signal, Patchcord, Receiver, 36", TriPaddle, 22 AWG White Twisted Pair, Single Ended ( 5 Amps).
-
product
Signal, Patchcord, Receiver, 72", QuadraPaddle, 22 AWG White, Twisted Pair ( 5 Amps)
7-124439000-072
Signal, Patchcord, Receiver, 72", QuadraPaddle, 22 AWG White, Twisted Pair ( 5 Amps)
-
product
Signal, Patchcord, ITA, 36", TriPaddle, 26 AWG Twisted Pair White/Black, Single Ended (1.5 Amps)
7-105426000-036
Signal, ITA, TriPaddle (7 Amps) 26 AWG Twisted Pair White/Black (1.5 Amps)
-
product
CXA Signal Analyzer, Multi-touch, 9 kHz to 26.5 GHz
N9000B
Master the essentials in signal characterization with the leading low-cost tool in signal analysis Perform cost-effective stimulus response measurements with the optional built-in tracking generator Add crucial functionality with X-Series measurement applications Enhance theory with practical skills when used with a training kit in your RF & microwave education lab
-
product
Signal, Patchcord, Receiver, 36", QuadraPaddle, 22 AWG White, Single Ended (5 Amps)
7-124922000-036
Signal, Patchcord, Receiver, 36", QuadraPaddle, 22 AWG White, Single Ended (5 Amps).
-
product
Signal, Patchcord, ITA, 72", QuadraPaddle, 24 AWG White, Single Ended (3 Amps)
7-121924000-072
Signal, Patchcord, ITA, 72", QuadraPaddle, 24 AWG White, Single Ended (3 Amps).
-
product
12GHz 16-Channel Signal Generator 19" 3U Rack Module
LS12916R
The LS12916R, 12GHz 16 channel RF Analog Signal Generator, offers industry leading performance, in a 3U, 19” space efficient, rack-mounted box. The LS12916R features 16 phase coherent channels, exceptionally fast switching speed, superior signal integrity and purity and all the necessary modulated signals for analog communication systems. With the highest channel density in the market the LS12916R offer the ideal solution for applications requiring high channel count at minimum space and cost.
-
product
PXIe-5663E, 6.6 GHz PXI Vector Signal Analyzer
781259-02
6.6 GHz PXI Vector Signal Analyzer - The PXIe‑5663E offers wide instantaneous bandwidth and supports RF list mode, which increases multiband measurement speed with fast and deterministic changes in configuration. You can use a PXIe‑5663E as either a spectrum analyzer or vector signal analyzer, and you can use it with the Modulation Toolkit to analyze custom and standard modulation formats. The PXIe‑5663E can perform measurements for a broad range of communications standards such as GSM, EDGE, WCDMA, WiMAX, LTE, Bluetooth, WLAN, DVB‑C/H/T, ATSC, and MediaFLO. Because all measurements are software defined, you can reconfigure the measurements using standard-specific toolkits. With these toolkits, the PXIe‑5663E provides a low-cost solution to high-performance RF measurements.The PXIe-5663E comprises the following modules:• PXIe-5601 RF Signal Downconverter• PXIe-5622 IF Digitizer• PXIe-5652 RF Analog Signal GeneratorThere is no physical device named "PXIe-5663E".
