Filter Results By:
Products
Applications
Manufacturers
Torque Transducers
transduce rotational energy.
See Also: Torque, Torque Sensors, Torque Testers, Torque Meters
- Pickering Interfaces Inc.
product
PXI Strain Gauge Simulators & Pressure Transducer Simulators
We offer simulation modules for Strain Gauge Simulation – used in mechanical systems to measure the tension or compression of structural components. These modules may also be used to simulate Wheatstone Bridge Pressure Sensors/Transducers. Simulation requires extremely fine setting resolution with high accuracy and temperature stability.
-
product
Run Down Adapters
Testing power torque tools is essential for product quality and regulatory compliance. A run down adapter is designed is to simulate the fastening process of a screw. Mountz run down adapters improve testing repeatability by adjusting for the impact force and irregular peaks of power tools. Mounted in-line between the tool's driver and transducer, a run down adapter provides consistent and reliable torque readings.
-
product
Custom Industrial Torque Sensors
Datum Electronics are able to provide both modular and custom designed torque and rotary strain measurement solutions, which can be complete as one off or as fully integrated OEM solutions.In many cases, it is better to use an existing shaft or test rig and use custom industrial sensors instead. This process reduces the cost of fitting a conventional torque transducer and it improves the torque measurements, taken by maintaining the dynamics of the driveline.
-
product
Load Cell Transmitter
MODEL SST-HV
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
product
Torque Transducers
Procter & Chester Measurements Ltd
A transducer is a generic name that is a device which is usually electronic that coverts a physical attribute to a measurement signal.
-
product
Torque Measurement Systems
Proper torque measurement is critical in many assembly operations. AIMCO provides expertise and measurement equipment for all three phases - before, during, and after assembly. Tool testing and capability studies can be easily performed in the tool crib or lab. Fine tuning of torque settings and process verification are achieved on the assembly line with rotary transducers. Use our complete line of electronic wrenches for final residual torque testing.
-
product
Dynamometer
Dynamometers, force and torque transducers available in many models. Buy your dynamometer or force measurment products from Vetek!The difference between a load cell and a dynamometer is that the dynamometer is optimated for fast measurement.
-
product
Torque Transducers
Torque meter has been designed for measurement of static and dynamic torque on rotating machines, testbenches and automatic tightening systems. Torque meter measures CLOCKWISE torque with POSITIVEoutput in tension or ANTICLOCKWISE torque with NEGATIVE output in tension.
-
product
Digital Strain Gauge Sensor
ZET 7111
The ZET 7111 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or separate external tension gauges connected using half-bridge or bridge scheme.
-
product
Digital Strain Gauge Sensor
ZET 7110
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
product
Torque Cell Transducer
Unitech Scales And Measurements Pvt. Ltd
*UNITECH’S manufacturers two type of Torque transducers 1. In-Line Rotating Torque Transducers with / without speed sensors 2. Reaction Type Torque Transducers.*Transducer ranges from 1 Kg-m to 600 Kg-m with various types like Flange mount, Hallow type, Shaft mount, etc.
-
product
Auto Reversing Run Down Adapters
AURA
The AURA auto reversing run down adapters are designed to provide consistent and reliable torque readings for use with power driven torque control tools. The AURA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
product
Power Monitoring Dynamometer
90085
Model 90085 is designed to measure machine tool output. This model acquires the necessary torque and speed data needed to calculate the horsepower of the machine tool under test conditions. It is a portable, self-contained data acquisition and monitoring system consisting of three major components: a pneumatic brake assembly, a torque and speed transducer, and the control and display module.
-
product
Rotary Torque Transducer
M425
M425 rotary torque sensor with keyway shafts offers high accuracy of 0.1% and torque measurement range from 0-10Nm up to 60,000Nm as standard. It’s an inline rotation torque transducer, widely used for motor, gearbox and pump torque testing.Using a highly-accurate non-contact technique, the Datum M425 Rotary Torque Transducer and Torque Meter represent an ultimate torque sensor for anyone looking to measure torque, power, and speed with high accuracy and repeatability.
-
product
Dynamic Torque Sensing System
Advanced Telemetrics International
Are utilized in applications where conventional rotary torque transducers are not practical due to excessive shaft speeds, vibration, and dirty, oily environments.
-
product
Load Cell Transmitter
MODEL SST-LV
The SST-LV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-LV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-LV may be powered from 12-30 Vac or 10-48 Vdc. The SST-HV Has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
product
Measurement
Strain Gauge Meter
The program Strain gauge meter is intended for various strain gauge measurements with the use of strain gauge transducers (e.g., force and torque transducers, RPM sensors, bridge and half-bridge circuits based on strain gauges, etc.) and a measurement module for strain gauges ZET 017-T.
-
product
Strain Gauge Sensor
ZET 7010
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
product
Testing Aircraft Tachometers
The test bench is comprised of a TMB 304 Torque Transducer and a custom fixture for the tachometer and corresponding inertia wheel. A servo motor is incorporated to provide speed to the tachometer. The entire drive train is conveniently mounted on a base plate with the appropriate couplings, bearing support and flywheel.
-
product
Auditor High Capacity Test Stands
Designed for testing tools with continuous rotating output spindles. The test stand includes a rundown fixture, bushing for side load support, reaction post or reaction paddles, transducer and torque analyzer display.
-
product
Life Cyclic Durability Testing
Environment Associates can provide everything you need for cyclic durability testing and performance fixturing. Services include mechanical cycling to a position or load, fatigue cycling to a fixed load, rotational torque cycling, and simple push/pull cycling. EA can design your fixture with electro-dynamic, air, or hydraulic assistance to mechanically move your part. All of our fixtures can be manufactured to withstand a wide range of temperature, humidity and vibration inputs. If required, forces can be monitored electronically, using a wide variety of inputs (i.e. strain gages, load cells, rotational transducers, thermocouples, shunts, and more). EA can create holding and check fixtures to perform “pre” and “post” evaluation for dimensional issues that may occur during testing. EA can provide fixtures for single tests run internally for EA test labs and can manufacture fixtures to be purchased directly by the customer for their internal use.
-
product
Torque Transducers
Interface offers both reaction and rotary style torque transducers.Whether you need torque transducers for rotary torque, axial torsion or reaction torque, you don't have to be an expert in torque measurement, because we are. Talk to us about what sort of torque you need to measure, and under what conditions and constraints. We'll walk you through the specification process, quickly and efficiently, and if we don't have what you need on the shelf, we'll be happy to customize an existing product or build a new one from scratch to meet your exacting requirements.
-
product
Torque Calibration
ISO 17025 Accredited Calibration for Torque Screwdrivers, Torque Wrenches, Torque Multipliers, Torque Transducers, Torque Watches, and Torque Readout
-
product
Load Cell Amplifiers
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
product
Motorcycle and ATV Dynamometers
Wide medium inertia roll assembly with our machined-in "traction grooves," quick-adjust wheelbase front mount, dual roll-on ramps, tie downs, casters, roller guards, eddy-current absorber (with a step-up drive), full-bridge torque arm transducer, electronic auto-load control, DYNOmite data-acquisition computer, DYNO-MAX software, inductive RPM pickup, AC power supply, and data wiring harness.
-
product
Wireless Torque Sensor Systems
Advanced Telemetrics International
are utilized in applications where conventional torque transducers are not practical due to high shaft speeds, vibration, and dirty, oily environments.
-
product
Data-Acquisition Computer
DYNOmite data-acquisition computer with from 3 to over 112 channels (with or without optional LCD display and pushbutton handheld interface), full-bridge strain- gauge-equipped electronic load cell torque transducer, AC power supply/recharger, data wiring harness, engine-temperature thermistor, and protective carrying case.
-
product
Run Down Adapters
Screw RDA
The screw run down adapters are designed only for EZ-TorQ analyzer. These devices provide consistent and reliable torque readings for use with power-driven torque control tools. The RDA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
product
Torque Transducers, Torque Sensors and Torque Meters
Torque Sensors and Torque Transducers [Nm]The HBM torque range includes sensors and transducers for precise torque measurement.
-
product
6-Component Wheel Force Transducer
Whether vehicle dynamics tests, brake tests or determination of load spectra - the new 6-component Wheel Force Transducer WFT-Cx measures all forces and torques acting on the vehicle with high precision. The robust housing reliably protects against dirt, water and snow and allows applications in any weather.
-
product
Rotational Rheometer
ARES-G2
The ARES-G2 is the most advanced rotational rheometer for research and material development. It remains the only commercially available rheometer with a dedicated actuator for deformation control, Torque Rebalance Transducer (TRT), and Force Rebalance Transducer (FRT) for independent shear stress and normal stress measurements. It is recognized by the rheological community as the industry standard to which all other rheometer measurements are compared for accuracy.
