Filter Results By:
Products
Applications
Manufacturers
3D Solder Paste Inspection
checks form, height, surface area, bridges, volume, x/y offset and coplanarity of solder. AKA: 3D SPI
See Also: Solder Paste Inspection, 3D SPI
- Pickering Interfaces Inc.
product
25-Pin D-Type Female Solder Bucket
92-960-025-F
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
product
High-speed 3D Solder Inspection Machine
YSi-SP
a high-speed 3D solder paste inspection machine that enables high-speed high-accuracy inspections based on our “1-head solution” concept for using a single type of head to handle various inspections. It is used to inspect the printing quality (volume, height, area, misalignment) of solder paste after it has been printed onto PCBs. Available April '18.
-
product
3D SPI Series
MS-15
- Exclusive 15MP / 25MP CoaXPress Camera System- Dual Projection Shadow Free Moiré Technology- Precision Compound Telecentric Camera Lens- Automated Z-Height Calibration System- Automated PCB Under Board Support System- Precision PCB Warpage Compensation- Closed Loop Communication With Screen Printer- Absolute Repeatability and Reproducibility- INTELLISYS® Industry 4.0 Intelligent Factory Automation System
-
product
3D Solder Paste Inspection (SPI)
Systems designed for solder paste inspection (SPI) quickly and reliably check the solder paste deposits on the circuit board.
-
product
Solder Paste Inspection System
KY8030-3
The new KY8030-3 delivers 3x fasterinspection without compromisingperformance and accuracy.Using patented dual projection,the system eliminates the criticalShadow problem that all 3D SPI systemscan be vulnerable to.Additionally, the new KY8030-3 has solvedthe PCB Warp problem that seriouslyimpacts inspection accuracyand reliability of result.
-
product
AOI & SPI, Test Systems
SigmaX SPI
Most defects in the circuit-board assembly are due to the solder paste or the process of printing solder paste. Since the transition to lead-free soldering, a whole new spectrum of problems has emerged in older paste printing and its due processes. Incomplete coalescence of ball grid array (BGA) spheres and solder paste deposits are failure modes that have increased in frequency since the transition to lead-free soldering. The SigmaXs inspection technology is unaffected by varying materials, surface conditions, or colors. The system profiles the board to generate accurate 3D shapes far superior to other brands and technologies.
-
product
3D Solder Paste Inspection
aSPIre 3
Industry-leading measurement accuracy and inspection reliability- Perfect solution to eliminate shadow problems, base plane settings, and problems with projection direction- Full 3D foreign material inspection solution for the entire PCB- High productivity through the highest accuracy
-
product
5D SPI
On Mek Solder Paset Inspection systems, items which are better inspected in 2D, such as area offset and bridging, are viewed in full colour. Using colour inspection the ISO-Spector S2 SPI can tell the difference between paste, solder mask, silk screen and other PCB features and the SPI system can intelligently give you accurate results. Volume and height measurement in 3D are combined with the 2D inspection in Real-time, to give a True colour 3D image. Other 3D SPI systems only inspect in the 3rd dimension, (Z axis) and make extrapolated assumptions about the 2D image.
-
product
3D Inline Solder Paste Inspection System
TROI 7700 SERIES
Using Moire' pattern, Pemtron's three-dimensional lead applicationdosage tester combines 2D color images with 3D measurement data toprovide more detailed, near-real PCB images, unlike traditionalcolor maps. We will also provide you with the best solution forhigh-quality and high-precision PCB production with a varietyof statistical programs, along with information you need toquickly and accurately judge positive/failure.
-
product
CyberOptics SE Series
SE Series
The CyberOptics SE Series offers the most accurate and repeatable, high speed 3D solder paste inspection in the market today. Utilizing the most advanced sensing technology, CyberOptics SPI products will provide manufacturers the reliability needed to compliment your overall screen print process improvement strategy.
-
product
3D SPI
Omron’s advanced inspection systems help manufacturers meet the requirements of today’s SMT applications while improving throughput and sharpening their competitive edge.
-
product
3D Solder Paste Inspection (SPI)
TR7007 SII
Offering inspection speeds of up to 200 cm2/sec, the TR7007 SII is the fastest solder paste inspection system in the industry. This highly accurate inline shadow-free solder paste inspection solution offers full 3D inspection at resolutions of 15 µm or 10 µm. Built on a high precision linear motor platform, the system's hallmark features include closed loop function, enhanced 2D imaging, auto-warp compensation and fringe pattern technology. Increase capacity without sacrificing additional space with an available dual-lane configuration.
-
product
2D/3D AOI Series
MV-6e
- Exclusive10MP/18MPCameraTechnology- Precision Telecentric Compound Lens Design- Eight Phase Color Lighting System- 10MP / 18MP SIDE-VIEWER® Camera System- Extremely Simple Programming and Operation- Integrated INTELLI-SCAN® Laser Inspection System- 3D Co-Planarity Inspection of Gull-Wing Leads, BGA and CSP - - -- Devices- Enhanced 3D Solder Paste Height Measurement Capability- INTELLISYS® Industry 4.0 Intelligent Factory Automation System
-
product
AOI & SPI Test Systems
Xceed AOI
Most defects in the circuit-board assembly are due to the solder paste or the process of printing solder paste. Since the transition to lead-free soldering, a whole new spectrum of problems has emerged in older paste printing and its due processes. Incomplete coalescence of ball grid array (BGA) spheres and solder paste deposits are failure modes that have increased in frequency since the transition to lead-free soldering. The Xceed enables true 3D measurement and provides the most accurate and repeatable inspection results with the minimum false calls. It’s designed with Advanced Signal Processing which gives results in noise-less, clear, and accurate 3D images.
-
product
3D Solder Paste Inspection system
PI Series
PI Series is a new generation 3D Solder Paste Inspection system that overcomes the limitations of traditional SPIs and satisfy all your inspection needs. The PI Series allows to easily implement Solder Paste Inspection in any PCBA line. These new generation systems are very intuitive to use, allowing non-experienced persons to get expected results.
-
product
3D Solder Paste Inspection Machine (3D-SPI)
3Si Series
Saki's 3D SPI identifies critical defects and assists with process improvement.
-
product
3D SPI Series
MS-11e
- Exclusive15MP / 25MP CoaXPress Camera System- Dual Projection Shadow Free Moiré Technology- Precision Compound Telecentric Camera Lens- Automated Z-Height Calibration System- Automated PCB Under Board Support System- Precision PCB Warpage Compensation- Closed Loop Communication With Screen Printer- Absolute Repeatability and Reproducibility- INTELLISYS® Industry 4.0 Intelligent Factory Automation System
-
product
Solder Paste Inspection
3D SPI
Checking all the relevant points in the production process is essential, especially in terms of analyzing the causes of defects, fixing them, and – most importantly – preventing them in the future. That’s why solder paste printing is of fundamental importance for manufacturing complex assemblies: If paste printing isn’t performed correctly, the defect can impact the subsequent assembly and the soldering process, resulting in a tilted component or a poor or missing solder joint.
-
product
Solder Paste
MVP Versa (3D SPI)
The first part of any SMT process is Paste. MVPs Versa and 900 Series platforms provide high accuracy paste inspection. High accuracy paste measurements are made using a choice of 10um or 5um 3D measurement systems.
-
product
Solder Paste Inspection Machine
3D SPI
The 6500 series is the measurement equipment provided by Jiezhi Technology for the small pads of solder paste printed on the PCB board. It will cause defects such as sharpness, offset, more tin, and less tin printing during solder paste printing. Causes defects in the later stage of production, this equipment can find problems in advance
-
product
Solder Paste Printers
Shenzhen Leadsmt Technology Co.,Ltd
Is mainly used to print the solder paste to the circuit board, is one of the essential equipment in electronic manufacturing.
-
product
Solder Paste Analysis
SPA1000
The SPA 1000 also introduces new process control capability by accurately measuring the suitability of the solder paste prior to its implementation on the production line. It achieves this by determining the "Open-Time" for the paste. It also performs the Slump Test and both of these methods provide a "Go/No Go" answer in less than 30 minutes to ensure minimum delay for the production line.
-
product
3D Digital Inspection
Digital stereo 3D imaging is a unique, advanced, stereo image presentation system designed to provide fully interactive real time natural 3D viewing and visualisation with outstanding depth perception.
-
product
Solder Paste Wetting Tester
SP-2
SP-2 is wettability testing machine forsolder paste, parts electrode and PC board,adopted SP-Tension-Method (Temperature Profile Method).
-
product
3D Measurement And Inspection
LOTOS
LOTOS automatic measuring systems can measure the full outer contours or individual areas of any measurement object quickly and precisely, irrespective of the shape, and test them for imperfections. The three-dimensional, non-contact measurement is carried out using optical measurement sensors with accuracy in the μm range. The result is a representation of the measurement object as a 3D model. Powerful, intuitive software allows the measurement results to be assessed extremely quickly.
-
product
Advanced 3D Automatic X-Ray Inspection
V810 S2EX
V810 is "3D Automatic X-ray inspection System" that corresponds to the double side mounting SMT-PCB that is not able to be checked by a transmission-type X-ray machine. It has the ability to detect a wide range of defects, and It have 100% complete defect detection capability in the Hip-defective.And, it is the inspection machine of world's highest level that combines the ability of the ultra-fast test speed and the lowest false call positives further.
-
product
3D Automated Optical Inspection
Zenith UHS
High-speed full 3D AOI that brings about a revolution in SMT process management Industry-leading speed for full 3D measuring inspection equipment skill solutions- Only solution in the industry to set inspection criteria according to IPC-610 standards- Performs defect diagnosis through measurement-based data and eliminates the causes of possible errors- Powerful 3D solder joint inspection
-
product
Solder Wettability Tester
5200 Advanced
This is an ultra-high-sensitivity wettability tester developed to evaluate the solder wettability of ever-miniaturizing electronic components. Electronic devices, especially mobile devices, are becoming more compact and multi-functional. As the number of electronic components mounted on them increases and the pitch of connectors that connect each device increases, soldering parts are becoming increasingly miniaturized. expected to respond to further miniaturization of electronic components and miniaturization of joints in the future .
-
product
3D Software
Geomagic Control X
Combined with the powerful and highly precise Artec 3D scanners, Geomagic Control X is a fantastic solution for anyone looking for speed, accuracy and a large variety of tools to choose from. Easily get the data required for extensive quality control in no time at all with Artec’s advanced 3D scanning solutions. Acquire precise measurements and carry out inspection and data analysis on the spot, using Geomagic Control X and an Artec 3D handheld scanner. Compare 3D scans to the reference CAD model to minimise assembly flaws and increase productivity.
-
product
Dimensional Inspection (3D Inspection)
The 3D measurement data from our scanners and PCMMs offers a comprehensive definition of a physical object that is used for measurement, inspection, comparison and reporting. When a part is defined by millions of points, you can see subtle deviations, slight variations and fine details, which gives you the confidence that a part (or mold) meets your specifications. To deliver the best of both worlds, we combine 3D scanning with our contact, touch-probe measurement tools to deliver precise dimensions on geometric shapes.
-
product
3D Scanner
Artec Space Spider
A new and enhanced precision instrument for CAD users and engineers, Artec Space Spider is a high-resolution 3D scanner based on blue light technology. It is perfect for capturing small objects or intricate details of large industrial objects in high resolution, with steadfast accuracy and brilliant color. The scanner’s ability to render complex geometry, sharp edges and thin ribs sets our technology apart. It is an ideal industrial 3D scanner for high resolution capturing of objects such as molding parts, PCBs, keys, coins or even a human ear, followed by the export of the final 3D model to CAD software.
