Filter Results By:
Products
Applications
Manufacturers
Harness
A multi-routed assembly of connectors, wire and cables.
See Also: Cable Assembly, Harness Test, Test Harness, Wiring, Wire, Connectors
- CAMI Research Inc.
product
Guided Assembly | Cable Harness Testers
Autobuild™ Software
Our optional, add-on AutoBuild™ software (Item 728) offers Guided Assembly for cables and wire harnesses. Use a supplied probe, or a finger with wrist strap, to touch an unterminated wire and the software shows (and says) exactly where the wire should be connected. As the operator attaches each new wire, AutoBuild checks the entire assembly and provides a clear checklist showing all completed good connections. When using our resistance-capable testers, you may connect diodes and resistors by name and value, check resistance values over the tester's specified range, and test conduction and isolation resistance against specified thresholds. Programmable tones accompany the graphic screen to give clear signals to the operator when good connections are completed or when incorrect connections, resistance violations, or diode insertions are detected. Combine with our Light Director™ option for light-guided assembly.
-
product
Harness Design and Manufacture
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
product
Cable Harness Test System
Data Patterns has built high reliability Cable Harness Test Systems for large installations. These are primarily used in launch vehicle aircraft and missile level cable harness test validation. Installations with upto 20,000 lines test capability at a single location have been supplied by Data Patterns. Portable version capable handling of as small as 384 points have also been addressed.
-
product
Harness Studio
Harness Studio is a browser for cable harness data, that brings together electrical and mechanical CAD-data into one program. It allows to navigate through very large cable harness data sets. Main aim of Harness Studio is being a tool that is very easy to use and allowing very flexible extraction of sub data sets.
-
product
Multi Trailer Tester Jobber Pack
#TSTPK1
Innovative Products of America
4 vehicle side trailer circuit testers and a three-way adapter.Test 7 flat, 7 round, 6 round and 4/5 pin trailers and receive a 3 way trailer adapter. Troubleshoot tractor trailer circuits Allows bypassing of troubled circuitry while on the road Eliminates guesswork "Winged" grip for easy removal from electrical connectorKit Includes:#7893: 7 Flat (Spade) Pin Trailer Circuit Tester#7865L: 7 Round Pin Circuit Tester (includes one brass jumper)#8000: 3 Way Trailer Adapter (7 flat pin to 6 round pin and 4/5 pin)#7897: 6 Round Pin Trailer Circuit Tester#7866: 4/5 Pin Harness Checker
-
product
Industrial ATX Motherboard With 12/13/14th Gen Intel® Core™ I9/i7/i5/i3 Processor
IMB-M47
ADLINK's IMB-M47 ATX Motherboard is a driving force behind industrial automation, supporting 14/13/12th Gen Intel® Core™ processors, and delivering substantial improvements in performance, capacity, and GPU support through its seven PCIe slots, PCIe 5.0 compatibility, DDR5 memory, and 2.5GbE PoE capability. Tailored for a range of industrial applications including automation, machine vision, factory automation, and logistics, the IMB-M47 features up to 128GB DDR5 memory at 4800MHz, supports three independent displays, offers USB 3.2 Gen2x2 (20Gb/s), 3x 2.5GbE LAN, multi-M.2 Key M, TPM 2.0 security, and PCIe 5.0 slots for high-performance add-on cards. Optimized for the latest Intel processors, this motherboard blends efficiency and performance cores, bolstering edge applications with swift memory performance via DDR5 technology. With a commitment to technology leadership, ADLINK equips customers with the tools to harness the latest processors, streamline real-time graphics processing, and fuel innovation in Edge AI applications, solidifying its role in the future of industrial edge computing.
-
product
6 Pin Round Pin Tester / Maintenance Kit
#8027
Innovative Products of America
Test, clean and restore 6 round pin trailer connections. Included tester will verify tow vehicle is sending proper signal to the connector, while cleaning tools remove corrosion and verify proper pin size on both male and female truck/trailer plugs. For use with 6 round connectors. Quickly tests, cleans and repairs truck and trailer connectors Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsPatentedKit Includes: #7897: 6 Pin Round Pin Tester, #8022: 6 Round Connector Cleaners, and #8030: 2 ml DeoxIT Cleaner
-
product
Metal Thickness Tester
Multigauge 5500 Waist
Mounts onto a belt or chest harness for hands free use. Bright LED display. Top display for convenient viewing.
-
product
Training/Verification/Demonstration Fixture | CableEye Cable Harness Tester
Item 802 (CB-T2)
This multi-purpose CBT2 fixture can be used for operator training, tester system verification, and facility verification.
-
product
4/5 Pin Trailer Harness Checker / Towing Maintenance Kit
#8026
Innovative Products of America
Test, clean and restore 4/5 pin trailer connections. Tester will verify tow vehicle is sending proper signal to the connector, while cleaning tool removes corrosion and verifies proper pin size on both male and female truck/trailer plugs. For use with 4/5 flat connectors. Patented. Extends harness life Great preventative maintenance tool Promotes safety and limits road hazardsKit Includes: #7866: 4/5 Pin Trailer Harness Checker, #8021: 4/5 Pin Cleaner, and #8030: 2 ml DeoxIT Cleaner
-
product
Truck Chassis Dynamometer
Truck chassis kit includes: heavy-duty tube-steel frame and 30"-diameter "dually" wide-roll assembly with machined-in "traction grooves," air brakes, diamond-tread deck plate, floor anchors, wheel chocks, vehicle tie downs, eddy-current absorber and controller with overdrive, S-beam load cell, DYNOmite-Pro data-acquisition computer, inductive RPM pickup, DYNO-MAX software, electronic auto-load control, 28-channel data harness, engine-temperature thermistor, and more.
-
product
Miller 400D
44550
No need to select ranges or adjust dials – the Miller 400D provides a direct read-out of resistance with the push of a button• Bluetooth interface allows optional data-logging via a Bluetooth-enabled PC (or PDA)**• Rugged, hard plastic case - safe to use on wet ground – IP67 rating for dust and water intrusion• Resistance measurement range from 0.01Ω to 10MΩ (auto-ranging) • High resolution digital display• Resistance measurements are unaffected by any stray interference signals that may be present in the earth during readings, due to the use of narrow band-pass filters centered at 82.2Hz (the unit’s operating frequency)• Runs on a set of replaceable D-cell alkaline batteries...no need to periodically recharge the unit or to plug it into a power source• Performs 10,000 single readings on a fresh set of batteries• Integrates with Universal Rectifiers’ Soil Depth Selector/Multi-Pin Cable Harness System (please see Integration with Universal Rectifiers’ Cable Harness)
-
product
5 ft Harness, 78-Pin Male Connector
GT96110
5 ft harness, 78-pin male connector on both ends
-
product
Spring Contact Probes
FEINMETALL offers a wide range of contact probe:ICT / FCT probes, short travel probes, double plunger probes, fine pitch probes, interface probes, wire harness probes, threaded probes, high current probes, switch probes, twist proof probes, push back probes, koaxial probes, radio frequency probes.
-
product
Threaded Probes Designed for Connector and Harness Test
Equip-Test Threaded Probes Designed for Connector and Harness Test
-
product
Robotics
Teradyne Robotics brings the power of advanced automation to companies of all sizes, everywhere. Our solutions – which include collaborative robots, autonomous mobile robots and motion control software for robots – are safe, reliable and easy to deploy.Through our robotics companies – Universal Robots and Mobile Industrial Robots – we enable you to harness the combined power of machines and human talent to improve operational efficiency. The result is better quality, better products and better business.
-
product
Electrical Circuit / Wire Harness Analyzer
ECAD System 2005
The ECAD System 2005 is a suite of test instruments for both lumped and distributed data for analysis of electrical circuits and/or wiring harnesses. ECAD is completely self contained, and has a built-in multimeter, impedance meter, TDR, and megohmeter.
-
product
Crossing Control Bypass Switch
XCBS-DL
The XCBS-DL is permanently wired into each crossing warning system, and can be configured with either a removable or non-removable bypass key. Simply connect the track connection harness to the designated track connection terminals. To prevent unnecessary operation of the crossing warning system, insert the key and select "bypass", rotate the knife switch to "bypass" and the crossing is disabled. When in the "bypass" position, a Dummy Track Load is connected to the track wire connections in parallel with the rails and the crossing approaches are shorted, preventing unnecessary activation when track equipment is working in the crossing approach circuit. The opening of one track lead may be desired to prevent unnecessary activation with intermittent shunting on the crossing approaches close to the crossing.
-
product
Wafer Sort
TestEdge offers complete wafer sort solutions. Our range of wafer sort capabilities demonstrates our ability to handle a wide range of devices and device characteristics. State of the art Electroglas probers Sort experience with high probe count Less than 4 mil pitch on probes Experience with C4 Bump and Aluminum pad Experience on Bipolar, CMOS, GaAs, & SiGe Overhead sort or cable harness sort Microsite testing capability
-
product
Services
Zebra Technologies Corporation
For today’s enterprises, IoT is no longer coming – it’s here and is pushing data processing power to the individual employee devices at the edge of your network. Being able to harness the power of edge-data is critical to maintain a competitive position within your industry. Whether it's understanding operational utilization, maximizing predictability and uptime, or simply unlocking the data of your edge devices, Zebra’s portfolio of services provides expertise every step along the way.
-
product
Custom Cable Assemblies
AMETEK Power Instruments has designed and manufactured electrical, thermocouple, and fiber optic harness assemblies for more than sixty years. We have the experience and capability to produce rigid and flexible harness assemblies for virtually any application, whether it is a missile ignition assembly, aircraft actuator assembly or a thermocouple harness for an industrial gas turbine. AMETEK Cable & Harness Products boast superior reliability, high temperature operation, numerous braiding options for abrasion resistance and EMI shielding, waterproof or environmentally sealed, and custom molding. For more information, please contact us.
-
product
1' Harness, 78-Pin Male D-Sub Connector
GT97104
1' harness, 78-pin male D-sub connector on both ends
-
product
Wire Harness Tester
NX Pro
The Dynalab NX Pro Wire Harness Tester is a low-cost, feature-packed, stand-alone continuity tester with a maximum capability of 512 test points. The flexibility of the NX System allows each program to perform multiple tests, display custom messages or sounds, and analyze the results of a test or an input to "decide" which operation to perform next. The NX Pro Tester has 1.3Mb memory capacity for program storage and is compatible with Printers, Scanners, and all other Dynalab NX System accessories.
-
product
Handheld Wiring Analyzer
HT-128
Simplify your wire harness testing. The DIT-MCO HT-128 provides a superior solution for point-to-point continuity analysis. These lightweight, handheld units can serve your diagnostic needs from product development and benchtop testing through field support and maintenance.
-
product
CableEye Tester Calibration Verification Board | Cable & Harness Tester
CB50
Populated with precision resistors, it allows users to determine empirically whether the tester requires calibration. The CB50 may be used on all CableEye models. The CB50 is intended for periodic verification of tester calibration. To ensure that resistance measurements remain accurate, CAMI recommends yearly calibration. However, depending on environmental conditions and usage, testers may need calibrating more or less frequently.
-
product
Cable and Harness Tester
CHT
The Cable and Harness Tester (CHT) provides multiple testing capabilities for up to 300 connector/harness test points. Test capabilities include DC Insulation Resistance (IR), DC and AC Dielectric Withstanding Voltage (DWV), and 2-Wire and 4-Wire Continuity.
-
product
LXI High Voltage Matrix 2-pole 300x2
60-310-302
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
PXI 24 Channel High Voltage Multiplexer
40-320-101
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
product
Snowmobile Dynamometer
Standard dyno kit includes: 9" toroidal-flow water-brake absorber, electronic torque-arm transducer, engine load control, DYNOmite handheld data-acquisition computer with backlit LCD and keypad interface option, AC power supply, stainless-braided hoses, puller bolt, data wiring harness, and protective carrying case.
-
product
Light-Guided Connector Assembly | Cable & Harness Tester
CableEye Light Director System
Our Light Director™ system (patented) provides a computer-guided technique for assembling connectors used in aerospace, medical, and other high-reliability applications. This system uses light fibers driven by super-bright LED lamps to individually illuminate target cavities in the connector being assembled. When the technician enters the wire code printed on unconnected wires, or touches a wire connected at the other end, the CableEye software turns on the appropriate fiber, thereby causing a bright, flashing light to project from inside the target cavity guiding the technician to the proper insertion point. Correct insertion is confirmed by the elimination of light from that location, whereas insertion into an incorrect location leaves the flashing light visible.
